Steel Pipe for Slumping

Steel pipe as opposed to stainless steel can be used for slumping. It will spall, so there will be a need to clean up the flakes of rust after firing. But since there is so much spalling, putting kiln wash or boron nitride is a waste of effort. Each firing will flake off any separator painted onto the metal. Cover the pipe with fibre paper instead - 0.5 mm at least.

You need to advance in temperature slowly as the pipe drains the heat from the glass where it rests. My practice is to advance the temperature at 100C/hr to 100C with a 20 minute soak, followed by 50% increases in rate to 250, and to 500 with 20 minute soaks before proceeding to the next segment. This probably is more cautious than necessary on all but the first segment.

Bubbles in Thin Pieces

Bubbles are often blown through frit castings and other thin pieces. This most results from insufficient volume of glass in the mould or on the shelf. Also the design can induce bubbles where there are thinner parts surrounded by thicker parts. As the glass softens, the surface tension of glass - from around 730 - causes it to pull up to equalise at about 6-7mm thick. This causes thinning in certain areas to allow thickening in other areas. This then leads to the risk of blowing bubbles through the glass where the glass has become thinner.

If thinner work is required, you can fire an over-sized piece to about 750C for a short time and then cut it back to the final size. If you want a flat thin sheet, you can also place the glass between two kiln shelves. You need to separate the shelves with a 3mm spacer to keep the upper shelf from coming completely down on the shelf, giving an extremely thin fragile piece of glass.

Diagnosing Fractures

What does the nature of the fracture tell about the reason for the break?

• incompatibility
• annealing
• adhesion
• splits
• lamination

Incompatibility

Fractures that follow the outline of a glass are normally indicators of incompatibility. The fracture starts at the incompatible glass and then - usually – goes directly to the nearest edge. Occasionally, the stress is not so great, so it only breaks around the offending glass without proceeding to the edge.

Annealing

A sinuous break – often with a hook at the edge – across the whole of the piece is generally an indication of one caused by an annealing stress. Inadequate annealing builds up stress within the glass that breaks through the whole piece in a lazy “S” pattern, rather than a straight line or following outlines of glass pieces.

Adhesion

Another kind of fracture occurs that is most often seen in ceramics. It is a kind of crazing that leaves the glass in granules. I call these adhesion fractures. This is indicative of the glass having stuck to the surface it is resting upon. This can be ceramic, steel or any other rigid refractory material. This comes from inadequate amounts of separator, often at high temperatures.

Split

Sometimes during slumps the piece can develop a tear or split in the lower surface without the upper breaking. This kind of split comes from heating the top of the glass more rapidly than the heat can penetrate the whole thickness. The weight of the relatively plastic upper surface overcomes the resistance of the lower surface by splitting it on the bottom face.

Lamination

Occasionally, a break will have both of the characteristics of incompatibility and annealing stress. The break is relatively straight and goes through differing colours rather than skirting them. This seems to happen most often on tack fused pieces and so is likely to be inadequate annealing. The annealing requirements of tack fused glass are much greater than flat fused glass, as the pieces are to some extent still reacting separately. If the whole piece is not given enough time for each piece to settle with the others they will contain unrelieved annealing stresses, which may have be too great to be held within the whole.

Observation

It is the monitoring and observation of the effects firings as they progress that allows confidence in setting firing temperatures and schedules. Although we all have busy lives, planning the firings so you can watch at the forming temperatures enables you to develop your firing practice much more rapidly than firing and waiting to see what comes out the next day. It means that in a single firing you can pretty accurately determine the temperature you need for firing that type of piece, rather than an number of separate firings.

You set your schedule - for the best guess that you can make - at the required temperature, rate of advance, and soak to achieve what you need. At about 50ºC to 20ºC (depending on your certainty) before the set point, you begin peeking to see what the glass is doing. When the glass has achieved the desired result, you advance to the next segment. You of course, have already refreshed your memory on how to do that from your kiln manual.

There is a method of opening and closing kiln to be safe and avoid disturbing the contents. Any observation ports should be opened first. The lid/door should be opened slowly and only enough to see what you had already planned to look at, to determine whether it is ok or a decision is needed for some other action. This opening should be only a few seconds. The air temperature will change dramatically, but the glass temperature will lag behind significantly, so a few seconds with the door only cracked open will not damage the glass at most temperatures. The exception to this is the annealing range – generally around 520C to 400C. The kiln should not be opened at these temperatures so that there is no disturbance possible to the steady and even annealing of the glass.

At temperatures above the annealing, you need to have protective clothing. At the minimum you need natural fibres such as cotton or wool, and eye protection. It is important to check with your hand the amount of heat coming from an observation port before moving your face toward it to look into the kiln. When the kiln is being opened even for brief periods, you should protect you eyes from the infra red given off by the kiln's interior. You should have something to protect your arms and chest too.

Always when raising and lowering the lid – or opening and closing the door – do it slowly to avoid creating puffs or billows of air moving through the kiln which might disturb the pieces at low temperatures or move debris over the hot glass at the higher end of kiln forming.

If the glass has not achieved what you want by the end of your soak, just extend the hold until the effect is achieved. You will have reviewed how to do that from your kiln manual before starting the firing. When the glass has achieved the effect you desire, advance to the next segment of the schedule as the kiln manual directs.

You then record the schedule including temperatures, rates, times, effects, etc. You should include a description of the project and its dimensions and nature e.g. full fused, tack fused etc. You will also want to include what this was fired on, what kind of mould – include its description. This will give you the reference for that nature of project for the future without needing to guess.

Recognising Devitrification

The appearance of devitrification varies from mild streaks as a dirty appearance on the surface, to at worst a granular surface that breaks away in small pieces. The glass will often have raised sharp corners in cases of severe devitrification.

Avoiding devitrification relates to cleaning, firing rapidly through the devitrification range, avoiding devitrification-prone glasses, and grinding edges as little as possible.

Repairing devitrification requires the removal of the devitrified surface. This can be done by sandblasting, sanding the surface by hand, using acid pastes to remove the surface. Then the piece needs to be fired again to a fire polish.

To ensure a polished surface a devitrification solution may need to be applied. It can be a commercial product or a borax solution.  Any devitrification solution should be applied evenly.

Spray nozzles

Quite a bit of the material we spray is solids in a colloidal suspension. This means that the nozzle can clog easily. Frequent agitation is needed to keep the material in suspension and not building up on the bottom which can clog the screen at the bottom of the tube.

You should not have long delays between spraying in one session, as the solids can begin to solidify within the spray head and so clog it.

When you have finished spraying, take the spray head off and clean it completely and thoroughly to ensure there are no solids left to harden. Then put it back together and it should be clear for the next use as well as sealing the container.

Stainless Steel Preparation

Preparing stainless steel rods and moulds for kiln work is done slightly differently from ceramic moulds.

Just to ensure that the steel is of the right grade, I fire it in the kiln to about 720C. This ensures that if the steel is not adequate for the high temperature work, you will find out that it spalls before the glass is put on top. It also has the advantage of removing any dirt and oils on the surface of the metal.

The separator that you need to put on the steel can be done cold if you use MR97 or other boron nitride coating. Its main advantage is that it can be put on cold and also that it has a very smooth surface. This should be put on thinly, or it will come off onto the glass.

You can also put standard kiln wash on the metal. The metal needs to be dry and clean. It could be sandblasted if desired for a bit of extra “tooth”, but is not normally necessary. Heat the metal to about 120C – 150C in the kiln. Remove it from the kiln with tongs or similar thing to grasp the hot metal. Spray or paint the kiln wash solution onto the hot metal. Return it to the kiln as necessary until you have a coating all over the metal. It does not have to be even all over, but noes need to have all of the metal covered.

If the kiln wash boils off the metal, it is too hot. So turn the kiln down a bit.

If the kiln wash runs off without sticking at all, the metal is not hot enough and needs to be returned to the kiln to heat up.

It is best to avoid applying the kiln wash to the metal in the kiln, as water and the hot elements do not mix well.

Making Tests

Every time you get a kiln that is new to you – whether new or second hand – you need to do some tests. Recording these tests is essential to your future work.

The first test is to get to know your kiln – where are the hot and cool spots, what effect does the kiln produce at a given temperature and soak. A very good guide to knowing the temperature differentials in your kiln is given by Bullseye Tech Note 1 – Knowing Your Kiln 

The second test is to make a series of small scale tiles to know what your kiln does at different temperatures and rates of advance. What combination of rate and temperature gives the roundness, degree of tack, flat fuse that you want.

How does the kiln perform in slumping and what are the effects of thickness and number of layers on the rate of slump.

These are elements that you may feel are a delay in being able to experience the enjoyment of fusing. However, they are essential to the long term enjoyment and success of your fusing activities.

Writing a Schedule

Making your own Schedule

I've been asked about making a schedule rather than using a pre-programmed one. My response is this, but please join in with amplifications and questions.

In principle, a firing schedule for glass follows these stages:

1 – a gradual, steady heat up to a temperature above the annealing point to avoid thermal shock

2 – a soak or slow rise around the slump temperature to allow any air to escape

3 – a more rapid rise to top temperature to avoid devitrification

4 – a rapid fall in temperature to an annealing soak, saving time and avoiding devitrification. The soak at annealing temperature is to equalise the temperature throughout the glass

5 – a steady slow fall in temperature to well below the lower strain point to complete the annealing

6 – a controlled cool to near room temperature to avoid thermal shock.

The details of schedules can appear complex, but the purposes of these six stages are reasonably simple.

Segment 1 is to heat the glass evenly without causing it to break from too fast an increase in temperature. At minimum this steady increase in temperature must continue to about 40ºC above the annealing point. (This will be about 540ºC)

Segment 2. This segment can include a “bubble squeeze” to enable air to get from between sheets of glass before the edges seal, or it can be a separate segment in your schedule. The slow rise in temperature will occur from about 600ºC to 680ºC. The bubble squeeze soak occurs at around 660ºC to 680ºC. In both cases there is normally a soak of half an hour at least at the end of the range.

Segment 3 is to go through the devitrification range (say 700ºC to 760ºC) as quickly as reasonable, but usually no faster than 330C per hour.

Segment 4 is to get back through the devitrification range to the annealing soak, which will be as long as required to equalise the temperature within the glass. This soak time increases exponentially with the thickness.

Segment 5 is the annealing cool, which should be a slow steady fall in temperature to ensure the glass all cools at the same rate (to around 370C).

Segment 6 continues the cool, although faster than previously, and often is achieved by turning the kiln off and leaving it closed until room temperature.

A schedule for a 6mm piece up to 2/3 the size of your kiln could be even simpler:

Segment 1 - 220 dph to 670C for 30 minutes

Segment 2 - 330 dph to 800 (flat fuse) for 10 minutes

Segment 3 - afap to 516 for 30 minutes

Segment 4 - 80 dph to 370, no soak

Segment 5 - off

You may find a schedule that will work, but you still need to know why it works, or at least what each segment is doing. So, for example, you need to think about what a 15 minute soak at 225C will do. What is the glass doing at that temperature? What do you want to achieve in that temperature range? Is there another way to achieve your objective? These are the kinds of questions you need to think about so you can construct your independent schedule when you move outside the parameters of the pre-programmed schedules.

To make a schedule for yourself can be worrying. But you can see from this example that it does not need to be complex. The principles are simple, although the details can be confusing. It is essential to know something about how heat affects the glass and this Bullseye Tech Note is one of the best descriptions. 

Knowing what the heat up events are is useful too. 

Selecting a Kiln

Kiln Forming – Selecting a Kiln

You have been doing some fusing and slumping and now want to get into kiln forming in a serious way. So you need to get a kiln.

The basic kiln choices are ceramic vs. glass. The brand, model and size are up to you. But there is some helpful information on the advantages of each kind of kiln in this post.

Another consideration is the shape of the kiln. Generally the greater the area of the shelf in relation to its size, the better it will suit fusing and kiln forming. Oval kilns seem to waste some space, although they do not have cool corners like the rectangular ones do. Relatively deep and round kilns are best for casting and high temperature work.

Even before you buy the kiln you need to think about where you will be installing the kiln and that will have an effect on the model and size. Some considerations are here.

Think about the kind of work you want to do. This will change with time, but you cannot anticipate that now. Will you be doing jewellery scale, detailed work, lots of forming work, high temperature or even casting work. Each of these have different requirements.

Small kilns are best for jewellery and detailed work – they can be fired quickly and will reach the top and annealing temperatures with a minimum of delay.

If you tend to work larger then you should consider a kiln of about 40 cm square to start with, although smaller kilns will work if they have enough height.

Slumping and kiln forming put a premium on height. If you are going to be doing a lot kiln forming you should consider a kiln with at least 25cm from base to elements. Ex-ceramics kilns can be good for this.

If you are going to be doing a lot of high temperature work, such as casting, pot melts, pattern bars, etc. you might want to consider a brick lined kiln such as a ceramics one as they retain heat by design longer than those designed for glass.

There are a lot of models, so it is up to you to find the combination of style, shape, size and price that suit your present needs.