Showing posts with label Plating. Show all posts
Showing posts with label Plating. Show all posts

Wednesday 7 January 2015

Plating


Objective
The object of plating is to modify the original colour, either by changing the tone or the intensity. This will, for example, darken a piece of glass where it would otherwise be to bright; or it will modify the colour to better blend with the surrounding pieces.


A further use of plating is in conservation, where the additional detail is placed on a separate piece of glass and placed in front or back of the original.



Leads
In leading, you normally use high heart lead. This is lead with a heart of 7mm or 10mm instead of the usual 5mm. Other heights are available, of course. The 7mm heart will accommodate two 3mm pieces, but if you are using thick hand made glass, you may require the 10mm high heart.

Comparing the Arrangement
Try the glass combination with each piece on top. Often there is a difference in tone or texture. Choose the one that suits your composition best.


Cleaning
Before finally fixing the glass together, make sure they are very clean as there will be no opportunity to clean the inside again. Try to avoid finger prints on the insides while you do further work with the glass.

Sealing
Make sure the glass fits the cartoon lines. You will be sealing the two pieces of glass together, so there is no opportunity to change the shape later. There are a variety of traditional methods of sealing the glass, but the easiest modern approach is to copper foil the edges to ensure that no cement creeps between the pieces.

Fitting
You then fit the glass into the came as for thiner pieces. Where you have a combination of heart heights, you can simply slip the ends of the lower heart cames inside the leaves of the high heart leads. The differences in height are small enough that no special support is needed for the thinner glass unless you feel better with the single layers of glass supported above the work surface.


Thursday 25 December 2014

Plating in Copperfoil

Plating is used to modify the colour, or intensity of local areas in a window or panel. Plating for leaded glass is normally putting two pieces of glass in the same came, although there was a common practice at the turn of the 19th into the 20th century to have the plate cover several pieces of leaded glass. In principle, the plating of copper foil panels is the same as for leaded glass, except there is no came to fit the glass into. So there are some variations.

An example where the fruit and leaves are all plated


Build the flat, single thickness window first. This provides a solid panel to work on. It also enables you to see whether you really need the plating, and if so the exact areas where it will be applied.

You should solder the whole panel except where the plate is to be soldered. In this/these areas just lightly tin the back, although you will have already put a solder bead over the whole of the front.

Patina the back of the panel, except where the plate is to go. Allow this to dry and clean up any spills, especially in the neighborhood of the plating.

Foil the plate with a backing to match the colour of the patina. So use copper-backed foil where the panel is in copper patina, but black-backed where the patina is black.

Tin the foil on the plate with solder. If the piece is to cross a number of the base pieces, you need to patina the tinned face that will be placed toward the viewer with the same colour patina. You need to make sure this is absolutely dry before proceeding.

Clean the plate and the base glass where the plate is to cover very well. Make sure there are no oils or tarnish on the solder, and that everything is dry.

Solder the plate to every seam that it contacts with no flux and a small amount of solder. This is to insure there is no leakage of flux - by not using any - or solder between the two pieces of glass.

Put a small amount of clear silicone between the edge of the plate and the base glass where you were not able to solder. Just lightly fill the gaps to ensure a seal against moisture and insects.
When the silicone has cured, carefully patina the plate so no fluid seeps between the glasses.

Protect the uneven back when handling by placing a soft foam pad, or a polystyrene sheet with cutouts for the plating, on the back to protect the panel from the carrying board.