First Kiln Selection

Glass fusing works best in top fired kilns.  Glass casting and some tall work are best with side or bottom elements too.  Compromises can be made of course.  The comparison of glass and ceramics kilns is important to understand.  

Kinds

Most of the following types of kilns are available for glass purposes.

Front loading.  These are good basic, multi-purpose kilns with good viewing properties.

Bell kiln.  This is where the whole of the heating chamber lifts up from the firing bed.  This is more common with very large kilns and is usually combined with lifting gear.

Clamshell kiln.  This is where the firing chamber is hinged, usually on the long side.  This kiln provides access from three sides. It can become too large to reach to the back of the kiln, so these tend to be rectangular.  The lid can also become too heavy for ease of movement and support.

Top loading.  Often called a coffin kiln, there are very good for casting or deep work, but are hard on your back while loading.  They need peep holes at appropriate levels to be able to monitor progress of the firing. These tend to have smaller floor areas than the clamshell.

Car kilns.  These are those where the firing chamber lifts like a bell kiln, but has the firing base on rails or tracks to move multiple firing bases under the firing chamber.

Modular kilns.  These are normally rounded kilns where each ring is controlled separately and can be placed on top of one another.  This is good for large heavy castings, as the refractory and glass reservoir can be placed on the base and the rings built up around the work.

All these kilns come in a variety of sizes.

Choose a kiln relevant to your current work.

The first thing you must decide is the kind and scale of work you intend to do in the near future.  It is too difficult to predict how your work might progress based on experiences with your current work.  It is better to by a smaller kiln that is ideal for the current work and then move to a different kiln, if necessary, or a kiln for different styles or scales of work.

The general advice is to buy as large a kiln as your budget and space and electrical installation will allow.  This remains the case with some precautions.  Think about how often you will fire - daily, a few times a week or a few times a month.   Think about how long it will take to fill the kiln.  A large kiln can take days or even a week to fill with small works. This would really limit the variety of things you could do in that period.  You would have to wait to slump until you had enough things fused to fill the space.  Indeed, you would need to have more moulds than if you had a smaller kiln.

I’m sure you can envisage a time when you will want to work larger than at present, but your first kiln will not become redundant.  It will continue to be useful throughout its long life.

Factors in the choice

Size. As already alluded, the size needs to fit with your current style and scale of work. 

Access.  How big a kiln can you get through the doorways?  How much bigger than actual external dimensions will the packaging make it upon delivery?  It is no use buying a kiln that must be taken apart, or all the packaging removed, to get it into your studio.  Of course, the wider the entrance(s) to your studio the easier it will be to get a larger kiln.  If you really need to have a large kiln, you might have to alter or move your studio space.  You also need to think about the kind of access to the studio.  Does the kiln have to come along the side of the house? Is the path paved or gravel? Stairs? Lift size? Parking for the delivery vehicle?

Space. The kiln also needs to fit into the space you have.  You will need about 15cm all around the outside dimensions for safety purposes.  This applies to ceramic kilns also, even though they routinely reach higher temperatures. The skin of the kiln does get hotter than is comfortable for your hand, but normally not hot enough to burn paper. You can reduce the front to back storage space by putting the kiln on wheels.  But the 15cm saved is not worth the time required to once again ensure that the kiln and shelves are level each time you move it. 

Accommodation also needs to consider access around the kiln to place work in the kiln, especially if you build elements in place on the shelf. 

Location within the studio is important, as the kiln needs to be near a power supply and in a place where it is away from the movement within the studio.

Power supply.  The nature of your power supply will also determine what size of kiln you should buy.  Note both the wattage and amperage required for the kiln and determine whether your household supply can cope with the energy requirements.  Usually a kiln can be run on household supply until it reaches the 1 metre² size, where three-phase power is required to have efficient use of the electricity.

Wattage. Kilns below the 1 metre² (approximately 1 square yard) in size have a need for at least 0.6 -1.2 watts per cm², or 4-8 watts per inch².  Once the kiln is larger, more power is required per area to accommodate the greater mass of the kiln.

Insulation.  All kilns require insulation.  This can be fibre or light weight brick, or a combination of the two.  These insulating bricks can be red hot internally, but only warm to the touch on the outside.  Generally, the refractory fibre – whether board or blanket – requires less energy to heat and cools more quickly in the critical devitrification range.  Most often the kiln floor will be made of brick to provide a firm base to support the kiln furniture.

Features

All kilns come with a range of features, many of them relevant to the size, but not all have the same ones, or the ones important to kiln forming.

Viewing ports.  These are variously called vents, ports, bung holes, etc.  Their importance is at least three-fold. 

·        These provide an opening(s) for you to view the progress of the firing, so you can add more time or heat, or skip to the next segment when adequate heat work has been completed earlier than expected.

·        They provide a means of venting the kiln.  This is important in the burn out of any fibre paper binders, and in allowing enough air to promote the oxidisation and maturation of the hot enamel colours.

·        These openings allow the kiln to safely cool more quickly at lower temperatures, say 300°C, but lower for thicker or more delicate pieces.

Opening.  The way the kiln opens is an important consideration.  Some kilns do not allow the kiln to be opened at all during firing.  This is not a desirable feature on a glass kiln.  It is important to have a switch that will turn the kiln off after a certain degree of opening, so that no contact can be made with a live element. 

·        A front opening kiln allows maximum flexibility to view the progress of slumps, drapes, tack and full fuse kilnforming.  It should have a switch to turn off the power to the elements after a certain degree of opening.

·        A top loading kiln allows you to add glass during a casting process, but is not suitable for working the glass during firings – E.g. combing, manipulation of a slump or drape.  This type of kiln occasionally has no allowance to open the top without turning off all the power to both the controller and the elements.  Avoid this, or have it changed.

·        A clamshell or bell kiln allows maximum accessibility during the loading phase and the forming stages.  Although a lot of heat is dumped forward, it is the easiest to use for combing and other manipulation of the glass during the firing. Again, this kiln needs a lid operated switch to cut the power to the elements when opened beyond a certain point.

Controller.  Although essential, controllers are often given as options, especially on smaller kilns.  There are at least two reasons for this.  There are a variety of controller styles and costs.  The buyer may already have their own controller, or wishes to specify the kind.  Controllers are significant costs involved in smaller kilns – sometimes being at least one-sixth of the price.  In general, the more features a controller has, the more it costs.

Controllers are often classified as “three-key”, or as full number pad.

·        The three-key controller – even if they have many more than three keys – is one where the numbers must be cycled through by holding an up or down arrow to change the numerical information.  This includes the programme number, segment number, time, rate, temperature, and sometimes other information. 

·        The full number pad controller will allow direct entry of numbers at each segment of the programming.  It will often have additional features, such as calculating the firing cost or kilowatts used, elapsed time, additional capacity for more saved programs, ability to control different areas of the kiln heating, etc.

Extras 

There are often things which will be worth considering purchase along with the kiln, but are not usually included in the base price.

Stands.  Smaller kilns range from table top - which do not need stands at all – through medium sized – which have optional stands – to larger ones that come with the stand integral to the whole kiln. Unless you intend to move your kiln about, it is not necessary to buy one of the metal stands. Even so, most of these stands come without wheels, so check that they do have wheels already attached.  If you will not be moving the kiln, you can use a wooden table with a refractory fibre board between the stub legs of the kiln and the table surface.  If the kiln does not have stub legs, you can set it on 4 house bricks. 

Kiln furniture. This consists of the refractory props and dams that will be needed in kilnforming.  The most essential are short (2.5cm) kiln posts to support the shelf.

Shelves.  Most shelves require a mullite/cordierite shelf to fire on.  This is a robust shelf that does not have the quartz/crystobalite inversions that ceramic shelves and tiles used for shelves have.  It is a good idea to buy one of these to fit your kiln at the time of purchase. Smaller kilns can use fibre board or vermiculite board as the shelf.  These can be purchased later.

Extractor fans.  These are available on many kilns. They are unnecessary on smaller kilns as they cool quickly anyway.  Larger kilns in a production environment may need quicker cooling, and these arrangements are very useful in those circumstances, but not others, as most kilns will cool in 8 – 16 hours without drawing air through the kiln.

There are a lot of other considerations in buying a kiln, but these are among the important ones, especially in selecting the first one.