Light Box Flexibility

Light boxes can be constructed in a variety of ways. The simplest to construct is the free standing, horizontal, single purpose light box.

You need to consider the size of the box in terms of surface area. This will relate to the space you have available and the scale that you work at. Having determined the surface area required or possible, you need to think about the height. The top should be of a height so you can stand or sit with a straight back while drawing, cutting or painting. This will vary according to your height and whether you will be standing or sitting. Typically these heights will be the heights of the benches and desks you already use, but you need to check again that you are actually working with a straight back, as this will reduce the fatigue you might otherwise experience.

Note that if the box is going to be sat at, it will need to be narrower to be able to reach to the opposite side. If you will be standing at the box, it can be at least half again as wide as the sitting version. A sitting version will also affect the depth of the box containing the lights. It may not be possible to have anything deeper than 100mm. This will produce some problems with the evenness of the light, but nothing that will make it unusable.

Then you need to consider the depth of the box. In principle, the deeper the box the better diffusion of the light. But there are limits. If the box is really deep, more lights will be required, and potential storage space is lost. I recommend about 150mm for the depth of the box. I then place the fluorescent tubes at 150mm centres across the box. It does not matter which direction they are oriented. That will be more determined by the available fittings and the dimensions chosen.

The flexibility you have in building your own box includes a number of things which could be constructed separately or in combination.

You can cover the light box with a sturdy work board to do all kinds of work on top. So this makes a combination light box and work bench. This top can be hinged so you don't have to lift it off each time you want to use the bench. It should have some support mechanism so it does not fall on your or your work. I have used a chain that allows the board to go back just beyond the vertical. These chains can sometimes get in the way of your work.

In addition to a separate surface the box can be an area of the work bench. The important element is that the rest of the surface of the bench should be at the same level as the light box top. Any variation runs the risk of breaking the glass you may be working on. The cover for this can be hinged to protect the surface when the light is not needed.

Often you will be working on pieces smaller than the illuminated area. It is possible to arrange things so that each light fitting can be turned on and off independently to allow light reduction or intensification as you need. It is simpler to have sheets of opaque card to place around your work area to reduce the extraneous light that will overwhelm the glass that you are selecting or painting, for example. In the case of too much light the glass or the painted lines and shading look darker than they really are as a result of your pupils contracting against the light.

You could add a variation to allow the light box to be used as a near vertical illuminated glass easel. This requires a set of hinges, a ledge on the hinged side and a support of some kind at the back, similar to a piano lid support. This is most useful in painting and in waxing up the pieces to view the whole panel before leading or foiling.

You need to think about the amount of flexibility you require the box to have when considering the materials to be used. If you want to use it as part of your display equipment, it needs to be mobile and so relatively light. This will interact with the materials to be used in construction. In this case you may want to make greater use of metals for their strength in relation to weight. 


 You probably will use opaque acrylic sheet as the surface. If you do, you will need to give it internal support to keep it from bowing. The best for this is another piece of acrylic – clear this time – glued to the top sheet and to the bottom of the box between the light fittings.


Additional information:
Uses
Requirements
Top surfaces

Lighting

Light Box Requirements

Once you have determined that you need a light box, buying or building seem to be the two options available.

It used to be that when hospitals were changing from film to screen based x-ray results, that the light boxes were available on the second hand market very cheaply. There may still be many available on the various auction lists.

The alternative is to make one for yourself. The materials are easily available and can be assembled with a little knowledge of wood working and basic electrical knowledge. The first element is to decide on what you want – the requirements.

Requirements

The top surface needs to be firm and scratch resistant. Toughened or laminated glass is good for this. The larger area covered, the thicker the glass needs to be, or there needs to be support under the glass to avoid breakage from pressure. The toughened or laminated glass resists breaking from dropping material onto the light box.

You need to have daylight corrected light sources for you light box, especially if you are doing any glass selection on it. Fluorescent tubes are easily available, but other light sources can be used. You need to have ventilation to allow the heat generated by the lights to disperse. Fluorescent tubes do not generate much heat and so are the common choice.

You need diffused, even light across the whole surface. This requires a diffuser and there are a number of solutions. You can sandblast the back of the top sheet, but I find this does not provide enough dispersion. You can sandblast both sides, which gives better dispersion of the light, but is difficult to clean and so needs another sheet on top. The best dispersion of light comes from using a sheet of opaque acrylic with about 80% light reduction. The difficulty with this is that it is flexible and needs support if any glass cutting is going to be done on the surface. I place the acrylic sheet underneath a sheet of 6.4mm laminated glass. This gives both solidity and dispersion.

Light is a central consideration in building the light box. The intensity is controlled by two things mainly – The number of lumens and the intervals of the light sources. The best way toward even light distribution even with good dispersion sheets, is to have multiple light sources. It would be possible to pack the box with light fixtures, but this is expensive and generates a lot of heat. It also may make the light too intense to be comfortable to work with. In general, fluorescent tubes placed at about 150mm centers apart will provide all the light you will need.

To make sure you get all the benefit of the light you need to build an enclosed box with ventilation holes or slots that is painted matt white on the inside. This allows the light to be reflected upwards through the surface with out bright spots that can be caused with gloss paint.

You need to consider the size of the box in terms of surface area. This will relate to the space you have available and the scale that you work at. In addition to a separate surface the box can be an area of the work bench, or covered by a separate work board – whether permanent or temporary.

The height of the box will need to be considered, Will you be sitting or standing while working at the light box. It needs to be high enough in either case for you to maintain a straight back.

You need to consider the ability to screen parts of the light so the light is directed only at the work area. Large areas of light will overwhelm the glass, making it appear darker than the finished piece will actually be.

You need to think about the amount of flexibility your box requires to have. If you want to use it as part of your display equipment, it needs to be mobile and relatively light. This will interact with the materials to be used in construction.


Additional information:
Uses
Light box requirements

Flexibility

Top surfaces

Lighting

Light Box

Light boxes are in many ways a development from the glass easel. These were used in studios to wax up the painted glass and display it as it would be seen in a window. Sometimes the glass painters painted across all the glass at once, so this method enabled them to see the results immediately.

Nowadays people tend to use back lighting for these and other purposes, so the light box has become more popular. Some of the uses are outlined here:

The light box is very useful when tracing or altering designs. The back lighting enables you to use other paper than tracing papers to transfer the design elements. You can fold the paper along the lines of symmetry to check on how the lines match, or to copy the lines from one side onto the other side at the designing and cartoon stages.

The light box can help select glass colours either initially or when the main pieces have already been established. The combination of the glass over light shows how they interact with each other. At later stages when the main glass is cut, it can help avoid unwanted bright or dull areas.

Possibly the most common use is in cutting dark or opalescent glass. The additional light allows you to see the cartoon through the glass and so cut directly from the cartoon. This can be enhanced by blanking out the excess light from around the glass or cartoon.

The light box enables the arrangement of the cut glass pieces to be assembled to view the colour balance and have a virtual view of how the panel or window will look as a finished piece. An additional step toward the result is gained if each piece is outlined in white-board markers – use black pens - to represent the lead or copper foil and their widths. This stops the light between the pieces from causing you pupils to contract, and gives a more accurate representation of the appearance of the final pane.  White-board markers can just be wiped off the glass without using spirits.

The light box is important in painting. The back lighting shows the effect of the painted line or level of shading immediately. This allows adjustments to be made quickly and accurately before firing,

Depending on how the light box is built, it also can be used as display lighting. This can be as up-lighting or backlighting.

Additional notes:
Light box requirements
Flexibility
Top surfaces
Lighting

Paper

The traditional approach to cartoons meant three versions were necessary. One with all the drawing details, one with the cut lines, and one for layout and leading.

If you are doing a leaded or copper foiled panel without details for painting on glass two copies are the maximum required. I make do with one original, as I have no place to keep the glass pieces laid out while cutting and beginning to lead, nor do I make templates for cutting.

The paper you need is one that is stiff enough to avoid changes in shape or wrinkling with changes in humidity. The paper also has to be robust enough to stand up to lots of movement. Cartridge paper from a roll works well, but is often seen as expensive. Brown wrapping paper is usually stiff enough, although thinner than cartridge paper.

Tracing paper is very useful, if you do not have a light box, as you can trace details from one version of a cartoon – whether new or from an old one – into another. However it changes shape when exposed to high humidity. To transfer the cartoon to more stable or more opaque paper, you can use a pounce wheel to transfer through the tracing paper for the final cartoon.

Two pounce wheels

If you have a light box you can use it to make the transfer, or you can stand at a window with the two sheets of paper taped together to trace the design onto the final cartoon paper.

If you need to make pattern pieces you will need a second copy to cut up. Here you need paper or card that lies flat. You may also find it useful to cover the main cartoon with a water proof covering if you are going to do a lot of grinding and fitting over the cartoon. You can do this by oiling your paper (as for stencils) or by sticking clear vinyl over the cartoon.

Soldering Radiating Lines

Some times no matter how you try to avoid it in the design, you end up with multiple solder lines joining at one point.

In copper foil work, I find it best to tin all the copper foil before assembly, as this means you can use a minimum of solder to tack solder the pieces to one another.

You will be left with less solder at the joint if you start from the joint and move away from it while soldering. This drags the solder into the bead line rather than letting the solder build up at the joint of the multiple lines and give a resulting high point resulting from the accumulation of solder there.

Kiln Furniture

You do not have to buy all your kiln furniture. Any refractory material – any heat resistant material that will stand up to the forming temperatures – that you have from broken shelves or used material will do.

The advantage to home made kiln furniture is that you can have exactly the shape you want. There are a number of possibilities.

Example of broken shelves

 Broken kiln shelves can provide supports and dams. They can be cut with a tile saw to give long strips that can be used as dams. Smaller squares and rectangles can be stacked to give height to other supports for the glass.

Cutting a shelf with a hand saw

25mm vermiculite board

Vermiculite in the form of a pressed board provides a medium strength kiln furniture. It can be cut with a wood saw, although it dulls cutting tools quickly. The board can also be carved with wood working tools although it is very abrasive, requiring tools to be sharpened before use on wood again.

25mm ceramic fibre board

Fibre board is not as strong or rigid as kiln shelves and vermiculite are, but is much more adaptable to curves and undulations. They can be cut with a knife and used with or without hardener – colloidal silica. If the hardener is used some kind of separator will be required to keep the glass from sticking. Dust masks are required for working with ceramic fibres.

Soft fire brick

Soft fire brick can be cut with a hand saw into many shapes and and sizes. They are suitable as supports and braces for dams.  There are also higher density bricks that are much heavier to resist the movement of dams.

3mm fibre paper

Fibre paper can be cut and stacked to provide shims to level shelves and moulds. Shapes can be cut into stacked layers of the material to provide dams for irregular shaped projects.

Uneven Slumps

Uneven slumps are an occasional feature of kiln forming. There are a number of possibilities that can cause this.

A mould that is not level will lead to an asymmetrical slump. You need to make sure on each firing that the mould is level, as well as your kiln and the shelf or supports. A three-way level can check this quickly.

Glass that is placed unevenly on the mould can cause uneven slumps. The glass should be placed on the mould so that it is equidistant from the edges of the mould all the way around. The glass needs to be level too. Again the three way level can help.

A slight bevel on the bottom edge can help avoid any catching of the glass as it moves within the mould.

Baffling or shielding parts of the glass can keep the heat off areas that tend to heat up faster than the rest and so begin moving before other parts of the blank.

Deep moulds most often present difficulties with uneven slumping. The best approach here is to use multiple, progressively deep slumps.

It also is possible to reach in with a wet stick and move the glass back to an even slump during the firing. Please observe all the safety requirements.

Most importantly, slow temperature rises solve most of the problems of uneven slumps. Fast temperature rises allow the component parts of the piece to absorb heat differently for different colours and glass of different viscosities. Slow rises in temperature help avoid any unevenness in the way the kiln heats the piece. Slow rises give more control and achieve the result at a lower temperature.

Note that a number of the solutions require observation while firing. The best results come from observing what is happening in the kiln. It allows you to make corrections either while firing, or – more often – in the next firing of a similar project.

Leaking Cutters

People sometimes comment that their cutters are leaking. Most cutters of the pencil type are not prone to leaking. Some of the pistol shaped cutters seem to have more difficulty.

One possibility is that the oil being used is too thin for the system that dispenses the oil. In that case a little thicker oil may cure the problem.

It may be that the oil is leaking from some where else than the valve or wick that is intended to dispense the oil. This sometimes happens when excessive pressure has been put on plastic handled cutters whether pencil or pistol. In this case, the alternative is to replace the cutter or use another method.

The other method could be called the dip and cut method. In this case you leave the reservoir empty and have a shallow container filled with oil soaked cotton wool. Dip the cutter wheel into the cotton wool before each cut and this will give you enough lubrication for the score. A variation on this is to dip a brush in a container of oil or turpentine substitute and paint along the line of the cut before scoring. Both are effective.

Although it is not a repair, you can push a cotton wool lump down to the valve or wick, saturate it with oil and then there is enough oil to lubricate the cutter wheel, without an excess to leak out. You do need to renew the oil for the lump of cotton wool from time to time.

Reworking Designs

Principles of design practice for stained glass, 5

Having created the design, you should consider re-working the designs for a variety of reasons. Some of these are:

- to save time in the later stages of the work. It all too easy in the excitement of creating a new piece to want to get directly on with making, however this often gives construction or design difficulties that have to be solved in the making, leading to compromises. In general far too little time is spent in the design stage. Time spent on the design will be more than saved in the construction and will produce a more satisfactory piece.

- to ensure the structural stability of the piece. Although reinforcement should be considered from the beginning of the design, this is the time to ensure that the piece will stand up to the use it will receive during its – expected – long life.

- Make sure you have investigated every possibility to answer the challenges of your design.

There are a number of activities that can help with these elements.

Reworking will enable you to maintain the essence of the design while simplifying lines and easing the labour of the construction of the panel. Often the design contains a number of lines that are not essential to the whole design.

As you re-work the design, you can make sure every curve, dip and angle are to your liking and so improve the whole. Redrawing also helps understanding of the design and the placing of lines. It will also help in considering the placement of lead came and the widths to be used.

Make sure the design is still structurally sound. The design should avoid long nearly straight lines with few interruptions, especially those that go from edge to edge in any direction. The lines should interlock rather than have many joins onto long lines.

It gives an opportunity to ensure that you can cut all the pieces. This is the time to look at the negative or background pieces to make sure you can cut them as well as the foreground pieces. Usually people are so concentrated on designing the main image that the background becomes too complicated to cut easily.

Make successive tracings with each change, so there is a record, allowing you to step back wards to an earlier version if necessary.

If this re-working stage leads to the realisation of design problems, there are some things that can be tried:

• Cropping the design can transform it. The focus of the design can be enhanced by removing some of the surrounding “information”. The change of proportions say from landscape to portrait can make significant differences.
• Enlarging and using only a portion of the original design can be a solution. This is similar to the cropping operation, but has the added advantage of making the pieces larger and easier to cut.
• Further simplification of background design lines can be considered. This will bring the focus back onto the main part of the image.
• Changing relative proportions can transform the design, e.g., by enlarging a busy background, it can be made simpler and easier to read the whole panel.

Elements of Design:

Designing for strength 

Colour selection

Design lines 

Design sources 

Reworking designs 

Design Sources

Principles of design practice for stained glass, 4

Use the everyday visual experience and make interpretations and adaptations. E.g.,

• draw lead lines on an illustration to make it suitable for stained glass, using the fewest lines possible
• Use your photographs of interesting subjects and scenes

These may never become useable designs or cartoons, but will increase you abilities to design from the real world toward the abstract.

Make and keep sketches as personal references. These do not need to be finished drawings, just a reminder of the thing(s) that caught your eye. Many artists always carry around a notebook to record these observations. Even if you only make drawings on paper napkins, make a folder to keep these separate sketches together.

Take photos of shapes and interesting images. These can then be used later to develop images.

Make up composite images by using overlays or collage. This helps develop your compositional abilities.

Work on abstraction in your design practice:

• Study abstract representations. Dissect – decomposition is a popular word - and analyse how the work is put together.
• Use geometric design as an introduction to abstract design. This forces your attention to structure, balance and colour.
• Once the distribution of the physical and visual weights is understood, this enables the jump to more free forms of abstraction.

Elements of Design:

Designing for strength 

Colour selection

Design lines 

Design sources 

Reworking designs 

Beautiful Design Lines

Principles of design practice for stained glass, 3

Stained glass is a graphic medium where line and colour are very important. Achieving pleasing lines and forms requires practice and use of various approaches and techniques.

The two dimensional world is one of abstract thought. Work and development are the way to creativity – there is no mystical talent. Practice drawing every day – set aside time to do it, if you normally shy away from drawing as an exercise.

Study and learn from what has gone before. Look at the images and objects you admire and analyse what you like about them and why. Also consider what things could have been done differently. Consider how those changes would affect the character of the piece.

Of course, maintaining your creative attention is difficult, so when blocks occur try some or all of these things:

• Put the work aside for a day or two before taking it out and looking at it again.
• Alternatively, pin up the design on a wall where you can look at as you pass by. When you see a change to be made, do it immediately and pin it back up.
• Get a new perspective, e.g.:
  • Turn it upside down. This will enable you to observe differences and spot inconsistencies
  • Look at it in a mirror. You might see people studying still life or live subjects together with their drawing in a hand mirror to get a new perspective that will help spot difficulties.
  • Put the design on the floor and climb a ladder to look at it. This provides distance and changes the angle at which you look at your design.

Remember that design tends toward realism or abstraction. You need to work on both forms, remembering that glass is a graphic medium that tends toward abstraction. Working on both forms develops your flexibility and knowledge. Having a working knowledge of both enables you to have a responsive approach to the client.

Elements of Design:

Designing for strength 

Colour selection

Design lines 

Design sources 

Reworking designs 

Responsive Colour Selection

Principles of design practice for stained glass, 2

The graphic form of much stained glass means that the medium is about line and colour. This requires that you think about both your and the viewer's response to the colour combinations. Respond to your instincts. Use you feelings about colour and their relationships. Try different colour ways. Formal training does help, but experience develops your skills. The individuality of the piece depends on the use of your instincts about the colour. There are some checks you can make while selecting colours.

Think of colour and impact. Hot colours tend to have more impact, as they give bright points or areas. Impact can also be created by using non-complementary colours together. If a more subtle impression is desired, use tonal variations without great contrasts.

Vary areas of colour and their proportions. This provides interest to a panel. It avoids a mechanical symmetrical appearance, even if the design is symmetrical

Think about colour balance. Although the colours may vary it is important that the weights of the colours are balanced so that the focus of the panel is not taken to another part because of the imbalance of the colour with the design.

When you are in difficulty selecting or arranging the colour, step back and view from a distance. This is one of several techniques to enable you to get a larger or different view. Others include viewing the design through a mirror, viewing through half closed eyes, look at the design from the other end, and viewing the design from acute angles.

When something feels wrong, trust your intuition and use other colours. Colour theory is just that -theory. It is through using your reactions that the piece becomes individual.

Seek out the nuances of the glass in tones and textures. These alter the perceived colour and weight considerably.

Keep the design lines simple when your emphasis is on colour, light and texture. This allows those qualities to dominate the panel, rather than the lines.

Always make a coloured drawing, before choosing the glass, as a reference. This is a rendering of your original idea. It provides a reference as you select the colours. It is something that can be altered, of course, but does provide an essential reference point.

Choose glass colours in the kind of light for which the panel is intended. This is essential, as the glass colour is subtly different in daylight, incandescent, and fluorescent lights.

Elements of Design:

Designing for strength 

Colour selection

Design lines 

Design sources 

Reworking designs 

Designing for Strength

Principles of Design Practice for Stained Glass, 1

There comes a stage when each of us moves from using patterns developed by others to trying to realise our own vision. This is the time where in attempting to reproduce an image from our mind or from natural and man-made forms that we begin to encounter difficulties with the medium of glass and lead or copper foil.

There are a number of principles that should be kept in mind while designing, or at least referred to when the design is reaching its final stages. This series of notes is an attempt to outline a number of the most important points in designing glass panels, especially larger ones.

Structural strength

The panel needs to be strong to last for a long time. Glass is a very resilient material; so is lead and solder. It would be a shame to design a panel in long-lasting materials that will not last because of the design and construction. There are some things to remember about creating a strong panel.

The strength of a panel is in its glass.

Glass in compression is stronger than steel. It is only when it is in tension that its weakness - or fragility – becomes apparent. So the structural arrangement of the glass needs to be such that each piece of glass supports its neighbours. It also needs to use shapes that are strong.

Avoid the following shapes:

• Hour glass shapes – those where the ends are wider/larger than the middle - will crack at the narrowest part. If the shape – usually a negative or background one – is necessary, break it up into smaller pieces that make sense in the whole design. It is also possible to add details that will break up these shapes, but be careful that the details do not detract from the whole.
• Exaggerated, deep inner curves will crack at apex of curve. If unavoidable, you should consider adding design lines where the glass would break anyway, or moving elements closer together so they almost touch to avoid the single deep inner curve.
• Thin long and tapering glass pieces will crack at the point or be covered by the lead or copper foil. Where you need to have such shapes, try drawing the lead or copper foil lines on the design. You can do this on a piece of tracing paper to avoid messing up your original design. This will show you how the finished panel may look. Alternatively, you can divide the long tapering piece of glass into several pieces so that any flexibility of the whole panel does not break the long thin piece. Short thin pieces are not so likely to be broken by any movement of the panel.

Lines radiating from a single point provide weak areas. This is due to long thin pieces of glass being liable to breakage. Break up long thin pieces of glass with lines. This ensures that the length of the glass is in a strong relationship with its narrowness.

Avoid “hinges” - lines that run from edge to edge – as that provides an area where the panel can bend. This is why windows made up of rectangular quarries need so much support and even then over time begin to concertina.

Don’t over complicate the cut lines. This makes for difficulty in cutting the pieces. Also the more difficult it is to cut the pieces of glass, the more likely it is to fail by breaking after being installed.

Elements of Design:

Designing for strength 

Colour selection

Design lines 

Design sources 

Reworking designs 

Re-Firing Holes

Occasionally you need to re-fire a piece that already has holes drilled into it. The smaller holes tend to close up or reduce in diameter when they are larger. There is a method to resist this and still have a neat smooth hole.

To keep the holes open during a re-firing, cut a strip of Thinfire a little thinner than the thickness of the glass to be fired, roll it up tightly and put it into the hole to be kept open. Starting the wrapping around a pencil or pen makes the start easy and the roll can be tightened by holding the centre and pulling the end.

Put the roll into the hole and allow it to expand to fill the hole. It does not have to be solid. If the roll is as high or higher than the surrounding glass there is a tendency to get spikes.

This works fine on 6mm and thicker glass, but I have never tried it on 3mm glass. No reason why it shouldn't work though in my estimation if you can cut and manipulate 2mm strips of fibre paper.

Slumping cracks

Cracks on the bottom of slumped bowls initially appear mysterious if not impossible.

It seems that what is happening is that the crack results from too fast a heat up.

The top gets plastic during a - relatively speaking - too quick a rise in temperature, while the bottom is still too cold to move. The piece splits on the bottom to relieve the stress of the weight of the upper portion of the glass. It does not break completely through, because the top is hot enough to move rather than break.

This bowl split as it was much thicker than I thought.  The firing was too fast and the top began to slump before the bottom was warm enough to move.  This is an extreme version of the split described above.

You need to put much more heat into the piece in the 50C above the annealing temperature if you experience this splitting effect. This can be done by a soak in the region of 540C-600C for Bullseye, or by a very slow rise in this region. The heating above this also needs to be slow to ensure the glass at the bottom of the piece is nearly the same as the top.

You will find that as a result of these slow rises or long low temperature soaks that the slump will occur at a lower temperature than with a rapid rise. This will also have the additional benefit of leaving fewer mould marks on the bottom of the piece.

Annealing Thickness

Factors relating to how to determine an annealing soak time and cool rate are numerous. The thicker the piece, the more conservative you need to be in the soaking and cooling. This is because the annealing soak time increases almost exponentially with the thickness of the piece. The reduction in the speed of the anneal cooling has an approximate exponential relationship also – requiring much slower rates of cooling.

In the simple case you use the smallest dimension to determine the thickness for annealing. The heat is assumed to travel the shortest distance to dissipate. Thus a piece cooled from both sides will be taken as the simple case. This needs to be modified in a number of circumstances.

1 - Pieces cooled from one side, as where the shelf is heat retentive, or fired on the base of the kiln can effectively cool from only one side. This doubles the distance the heat has to travel. So you need to use the numbers from any annealing table for glass twice the thickness of the actual piece.

2 - Then if you have variations in the thickness of the piece, you need to be more careful, because the thinner areas will cool faster than the thicker, giving the potential for stress creation.

3 - If you are doing anything less than a full fuse, you will need to be more careful. If the pieces are tack fused, they will in part, act independently of each other and so need more careful, slower annealing.

4 - The less symmetrical a piece is, the greater care needs to be taken, just as with differences in thickness.

5 - The heavier or more insulating the refractory materials that surround the piece, the greater the care needed in annealing.

A rule of thumb is to consider these variables and add to the soak times and reduce the speeds of anneal cooling in accordance with the number of variables exhibited in your piece. With the first of these variables - cooling from one side - use the schedule for twice the actual thickness of the piece. Then add another step up in thickness for each additional variable.

So, as an example, the most common complicating factor is the inability of the kiln to cool the pieces equally from both sides. This requires you to double the thickness to read an appropriate schedule from the table making the schedule for 12mm glass.

But your piece of glass also varies in thickness, so you need to add another step up in thickness, giving you 19mm.

However you are not intending to go to a full fuse, so you need to add another thickness. Now you are up to the table for 25mm.

But the pieces are asymmetrical, so another step up in thickness is required giving you 38mm.

And you have heavy dams under and around the piece, so yet another thickness level is required to read an annealing schedule from the table. This gets you up to 50mm as the part of the table you should be reading from. So you will need an 8 hour soak rather than 1 hour and need to reduce the temperature at 4C/hour rather than 80C/hour.

Of course, not every project has all these variables in it, so you use only those that apply, but each of those that do apply requires a step up in thickness to read the schedules for the numbers to plug into your controller.

This is a rule of thumb, so you will need to test any pieces for stress and learn from your experience if this is conservative enough for you pieces.

Copper Backings

“Is it possible to to fuse copper to the back of glass?

The easy answer is - no.

But it can be done. There are a number of conditions that will help.

The copper needs to be thin and flat. It works best if you clean the copper of any oxidisation, 
and then coat it with borax or other devitrification spray that can act as a glass flux.

The fusing has to be done with a long soak to ensure the bottom of the glass is as soft as the top to assist the attachment of the copper. The devitrification solution will help soften the glass next to the copper sheet. You also have to protect your shelf from contamination by the copper sheet. This can be done by using 3mm fibre paper under the copper.

Not all attempts will be successful, showing that this process is on the edge of acceptability.

It is easier simply to glue the copper to the back.

“Does it matter whether it has been fused already?”

The glass does not have to be fused prior to attempting to attach the copper to the back. If it has been fused, you need to run a slower schedule than when fusing glass for the first time. A schedule for slumping, but with a higher target temperature – at least fire polishing – will be required.

Ramp Speeds for Slumps and Drapes

I find that a steady slow heat up gives best results for both slumping and draping. Many do a two stage heat up with a slower initial rise to a temparature above the annealing point and then faster afterwards.

A slow steady increase in temperature allows all the glass to be nearly the same temperature both across the piece and from top to bottom.

Speed in draping, especially where there are different colours and thickness, promotes "wings" as any unevenness in the heat across the piece will translate into variable drape speeds. Allow all the glass to get to the same heat, by going slowly.

I proceed at the same speed from start to the forming temperature - no speed up at all. Yes, the glass will accept it a rapid heating to the target temperature, but it does not promote even slumps or drapes.

Candle Bridge Moulds

A candle bridge mould is one of the most difficult moulds to use successfully. The problems relate to the kinds of work you are trying to do, the size of the glass to put onto the mould, the shape of the piece and the stability of the resulting piece.

With a candle bridge you are trying to do a combination of slumping and draping at the same time. You are slumping into the middle and draping over the curved sides.

Additionally the candle mould requires the glass to fall into a small opening and this requires long soak times. Long soak times mean the glass that is draping stretches while the central portion is trying to fall into the opening. Of course, if you don't want the depression to be flat, you don't have to soak so long and the stretching effects on the draping part of the of the glass won't be so great.

It would seem logical to measure the mould around the drapery curve (or arc of the mould) and to the shape of the ends, but experience has shown me that this leads to glass that is too long along the sides and bent at the ends. So I cut my blanks for candle moulds as a rectangle without curved ends and then round the corners of the rectangle just a little by nipping them with my grozing pliers before fusing.

If you measure along the top and along the length of the mould you have a piece of glass that will be increasing in length at the draping part of the mould, meaning that it will fall off the curve and onto the draft (or side) of the mould. The draft is an angle from the vertical. Good moulds are made with a draft so that if glass were to fall over the edge it still will be possible to get the glass off the mould.

The draft on a mould means the diameter of a circular one is greater at the base than it is at the rim. And it is common to measure only the diameter at the rim.  In the same way the dimensions at the outside base of a rectangular mould are larger than the rim of the mould.

Back to the rectangular candle mould. The draft on this means that measuring the base of the mould is slightly wider than the curved part of the mould, but less than if measured around its curved portion.

Experience has shown that in the case of the candle moulds measuring the width of the mould is sufficient. There is enough height in the moulds I have used that it does not make any functional difference if the glass does not reach the bottom of the curve on the mould. It is better than hanging off the edge.

The length of the glass should be no longer than the shortest part of the mould's length. Cutting a curve into the glass to allow a small overhang produces a depressed lip because of the length of the soak required for the slump into the small aperture of the candle depressions.

My soak for candle moulds is 90 minutes at my process temperature. This gives me a flat depressed area for the candle to sit, but it also means that the draping glass has been stretching. And it also means that the glass will drape unevenly as the various colours absorb heat differently allowing some parts of the glass to stretch more than others.

The placing of the glass on the mould is absolutely critical. It must be exactly parallel to the sides of the mould. Any slight movement from that will induce a twist in the resulting piece allowing it to rock. Arranging it exactly right and placing some kiln washed furniture at each side to keep it in place until it begins to slump is an important aid.  
The glass will begin to bend before it sticks to the kiln furniture.

I have never been able to get a stable candle mould whether from 3mm or 6mm thick glass. I always have to grind the base a little to make a stable piece. I take it as part of the process, but careful placing reduces the work.

Cutting Box Hinges

Cutting the brass tubing for box hinges is best done with a saw.

The manual version is to use a fine toothed saw - similar to those used by jewelers – with very light pressure.

The power solution is to use a Dremel or similar hobby motor with a cutting wheel attached. This cuts through the tube cleanly and quickly.

In both cases, a fine rat's tail file can clean up any burrs within the tubing.

If you use the internal tubing you can cut both at the same time. However, it is quick and easy to use the appropriate sized copper wire to insert and then bend down onto the corner of the box. This gives greater flexibility and avoids waste.

Vase Cap Fitting

“Can anyone offer me any tips for fitting the brass caps onto lampshades?””

There are at least three ways to get the right vase cap size.

Make up your shade in a cardboard mock-up. Use 3mm thick card or foam board to represent the glass, as the thickness of the glass is important in determining which vase cap is the correct size. Try your vase cap against the cardboard model, then if you need, alter the pattern so the glass pieces meet at just the right place to make the lip of the vase cap fit just over the top of the glass. You can do this by either shortening or lengthening the pattern a little at the top edge.

The second also involves making a cardboard mock up. After making this maquette, choose a vase cap that overlaps the top opening, covering all the edges. The third option is to use two vase caps, one above and one below the opening to clamp them together trapping the edges of glass between them. Use a furling and lock nuts with no solder at all to hold the lampshade together.

A general discussion of panel lamp dimensions

Squaring Panels

When building leaded glass panels to be placed in existing wooden frames, you need to make sure the panel is as square as the opening in the frame. The first requirement is to make sure your cartoon is squared, or has right angles at each corner.

I use a “roofing iron” as it is called in the UK. It is a steel tool about 600mm on one side and 400mm on the other. Its original use was to work out the pitch of roofs and check the same pitch was maintained all along the building. The first important thing – now that all roof trusses seem to be prefabricated – is that they still are in production. The second thing is that they all have a fixed right angle.

Using this roofing iron will ensure your corners on the cartoon are right angles. This helps in the drawing of the cartoon as you only need set the iron on the base line and draw the verticals without having to measure the width higher up the cartoon. Of course you should check that the width is still correct at the top, just in case there has been a slip.

Then you have to stick to the cartoon.

When you are setting the battens to ensure the sides are held where you want them while you continue with the leading, the roofing iron again will ensure that you have placed the battens at right angles. You choose which line is to be your base, and nail or screw it into place. Ensure it is exactly parallel to your cut line and then align one side of the iron against it. Place the other batten snugly along the length of the other leg of the iron and you know you have a right angle.

When you are completed leading, but before soldering you can check on the accuracy of the angles by using the roofing iron again at each corner to check on the “squareness” of the whole panel. If the panel is out of square, you can tap on the battens not yet nailed/screwed in place to ease it all back into “square”