Silberschnitt Runners

 
The use of the highly acclaimed Silberschnitt cut runners requires a bit of experience to get the best from them.  They are at their best on inside curves and thin strips.  This is a few notes on how to make best use of the runners.

 

 
Always use the runners with the name visible to you.  This is the right way up.
 

Make use of the adjustable bar at the top of the runners.  Rotate the adjustable bar to be at right angles to score line.  This means the pliers do not have to be at a particular angle to the score line, which has advantages in tight areas.
 

Each press of the handles opens only a small run of the score.  Excessive pressure risks breaking glass and reducing the life of the pads

 

Move the runners along to the front edge of the opened score and press again.  Work your way all along the curve adjusting the angle of the bar as you go.  This progressive opening of the score line gives a break with almost no flares.
 

These runners are much better than the plastic ring star breakers, because there is much more control over angle of pressure.
 
Note: make sure you get replacement pads when you buy, they are robust but do wear out over time.).
 
 
Silberschnitt running pliers are excellent but require some experience to get the best from them.

Adjusting Cut Running Pliers

Typical cut running pliers

Cut running pliers are very useful tools if used correctly.  The pliers must have the curve in a “frown” rather than a “smile” to operate properly.  The knurled screw at the top and the scored line on the top jaw help place the pliers the right way up. They must be placed directly in line with the score. They should be only a centimetre or so onto the glass.  Holding them at the end of the handles, apply gently increasing pressure until you hear a click or see the score running.  If it does not run completely, turn the glass around and apply the pliers to the other end of the score.

Use of the Adjustment Screw

It is important to make use of the adjustment screw to get the best from the pliers.  If this is not adjusted properly, it is possible to crush the glass, or at the other extreme, not run the score at all.

The jaws need to be adjusted for the thickness of the glass.  The method I use for this is to place the edge of the runners on a corner of the glass to be scored.  

Loosen the screw until the glass is gripped by the jaws.  

Gradually tighten the screw until it resists your gentle pressure on the handles.  This gives you the correct opening of the jaws for that piece of glass.

When the pliers are properly adjusted to the thickness of the glass, you will not crush the glass and it is easy to use the pliers without cushions.

Using Cut Running Pliers Without Cushions

Using Cut Running Pliers Without Cushions

There are a wide variety of cut running pliers for different purposes.  A description of some of them is here.

This post is to describe maintenance and use of this kind of cut runner.

The plastic covers that come with these cut runners eventually wear out.  The replacements are hard to find. There are things you can do other than buying a new pair just for the shields.

You can dip the jaws in tool coating compounds such as Plastidip.  This does not last as long as the plastic, but is easy to re-do.

You can wrap the jaws in tape.  Electrical tape, duct tape or even self-adhesive elastic bandage will do the job. Again, not long lasting, but easy to replace.

Or

You can use the cut running pliers without any covering on the jaws.  “You can’t do that. You will crush the glass!” is the response I hear.  You can use them bare. I do, and so can you.

The key is in the adjusting screw.  It is there not just to tell you which is the top of the pliers; it has a function too.  That screw adjusts the opening of the jaws to the thickness of the glass. 

A simple way to ensure you have the correct opening is to put one corner of the jaw on the edge of the glass with the jaw opening less than the glass is thick. Then tighten the screw until you feel the handles of the pliers begin to open.  Then you have the right opening for the thickness of the glass. 

It ensures you cannot crush the glass, as the jaws will not close at the centre to be less than the glass thickness. 

You also have a more direct feel of the glass without the spongy connection of the plastic. You can sense the glass beginning to bend just before the score runs due to the gentle pressure of the jaws of the cut runners on either side of the score.

Whether you use the cut runners with or without cushions on the jaws, it is important to keep the adjustment screw lubricated so you can adjust the width of the jaw opening for different thicknesses of glass.