Glue Ratings
The glue used for chipping glass is generally called animal hide glue. Many companies sell animal hide glue, but to get the best results, you must use glue that has been formulated and tested for strength.
There are many grades available, such as:
80, 110, 135, 164, 192, 222, 251, 280, 315, 347, 379, 411, 444, 478, 512 jelly gram strengths
The three grades suitable for glue-chipping are:
5x (weakest) = 135 gram strength
4x (suggested) = 164 gram strength
3x (stronger) = 192 gram strength
Showing posts with label Glue Chipping. Show all posts
Showing posts with label Glue Chipping. Show all posts
Wednesday, 17 September 2008
Tuesday, 16 September 2008
Glue chipping, 8
Different Glue Weights
The main control over the chip design relates to the ratio of glue to water per area of glass.
140gms glue to 850 centilitres water per square metre is the minimum. The chip will be spotty or absent entirely.
425gms glue to 850 centilitres water per square metre gives the best results – a uniform chipping usually in a fern pattern.
570gms glue to 850 centilitres water per square metre gives a larger more iceberg-looking chip.
850gms glue to 850 centilitres water per square metre is wasteful and usually the glue is so thick the glass won't chip at all.
Experiment with the intermediate amounts to see what you get. Keep good notes of all the variables involved, so you will be able to repeat a pattern if you need to.
The main control over the chip design relates to the ratio of glue to water per area of glass.
140gms glue to 850 centilitres water per square metre is the minimum. The chip will be spotty or absent entirely.
425gms glue to 850 centilitres water per square metre gives the best results – a uniform chipping usually in a fern pattern.
570gms glue to 850 centilitres water per square metre gives a larger more iceberg-looking chip.
850gms glue to 850 centilitres water per square metre is wasteful and usually the glue is so thick the glass won't chip at all.
Experiment with the intermediate amounts to see what you get. Keep good notes of all the variables involved, so you will be able to repeat a pattern if you need to.
Monday, 15 September 2008
Glue chipping, 7
Variables Affecting Chipped Patterns
The glass chipping pattern is subject to many variables. The duplication and uniformity of each pattern is dependent on control of these variables.
There are many variables to be considered, The major ones are:
1. Glass - type and surface preparation
2. Room temperature during preliminary drying stage
3. Glue - type, concentration, and temperature at time of application
4. Weight of dry glue applied per area of glass
5. Dryness of glue film at end of preliminary drying stage
6. Temperature of drying room during chipping process
The glass chipping pattern is subject to many variables. The duplication and uniformity of each pattern is dependent on control of these variables.
There are many variables to be considered, The major ones are:
1. Glass - type and surface preparation
2. Room temperature during preliminary drying stage
3. Glue - type, concentration, and temperature at time of application
4. Weight of dry glue applied per area of glass
5. Dryness of glue film at end of preliminary drying stage
6. Temperature of drying room during chipping process
Sunday, 14 September 2008
Glue chipping, 6
Secondary Drying and Chipping Stage
The secondary drying and chipping stage is when a small space heater can be used to warm the glass up to around 52C (125 F). Do not point the heater directly at the glass. Keep it at least one metre away from the glass. You don't want to cause the glass to get too hot and crack.
This indirect heat will cause a rapid evaporation leading to curling of the glue and the chipping of the glass surface. The glass is under extreme stress at this point and should not be handled unless absolutely necessary. On sunny days the glass can be set in direct sunlight. This is the easiest way to get the glue to chip the glass.
The chips of glue can pop off and travel some distance, so take appropriate precautions, i.e. safety glasses, gloves, aprons. You might want to place a cloth over the surface.
After all the glass is chipped, some glue may still be left on the glass. The glue is water soluble, so you can soak the glass with warm water and scrape off the softened glue. Be careful of the extremely sharp shards that are now concealed in the water.
The glue and glass shards left from the chipping process can create a big problem if not cleaned up. Because the glue is an animal by-product, cats and dogs love to eat this stuff. This can cause your pet extreme harm and even death! Dispose of the waste carefully.
The secondary drying and chipping stage is when a small space heater can be used to warm the glass up to around 52C (125 F). Do not point the heater directly at the glass. Keep it at least one metre away from the glass. You don't want to cause the glass to get too hot and crack.
This indirect heat will cause a rapid evaporation leading to curling of the glue and the chipping of the glass surface. The glass is under extreme stress at this point and should not be handled unless absolutely necessary. On sunny days the glass can be set in direct sunlight. This is the easiest way to get the glue to chip the glass.
The chips of glue can pop off and travel some distance, so take appropriate precautions, i.e. safety glasses, gloves, aprons. You might want to place a cloth over the surface.
After all the glass is chipped, some glue may still be left on the glass. The glue is water soluble, so you can soak the glass with warm water and scrape off the softened glue. Be careful of the extremely sharp shards that are now concealed in the water.
The glue and glass shards left from the chipping process can create a big problem if not cleaned up. Because the glue is an animal by-product, cats and dogs love to eat this stuff. This can cause your pet extreme harm and even death! Dispose of the waste carefully.
Saturday, 13 September 2008
Glue Chipping, 5
Drying time
The glue will go through an initial drying stage. This is in the first hour or two, depending on the humidity and temperature of the room. Make sure to keep the glass level during this period.
The next drying stage takes between 12 to 24 hours. This is where the glue will cure and loose almost all of the liquid. A fan to circulate the air will speed up this process. The glue should be left to dry at its own rate, do not hurry it by heating. Uneven curing may result in a poor chip pattern.
The secondary drying and chipping stage is when the glue actually starts to peel or chip. The glue shrinks considerably during the total drying process. As it shrinks, it grips into the pores caused by the sandblasting and literally rips the top of the glass off.
Use precautions when handling glass that has a dried layer of glue. Goggles, gloves, aprons are the minimum precautions against the slivers of glass.
The glue will go through an initial drying stage. This is in the first hour or two, depending on the humidity and temperature of the room. Make sure to keep the glass level during this period.
The next drying stage takes between 12 to 24 hours. This is where the glue will cure and loose almost all of the liquid. A fan to circulate the air will speed up this process. The glue should be left to dry at its own rate, do not hurry it by heating. Uneven curing may result in a poor chip pattern.
The secondary drying and chipping stage is when the glue actually starts to peel or chip. The glue shrinks considerably during the total drying process. As it shrinks, it grips into the pores caused by the sandblasting and literally rips the top of the glass off.
Use precautions when handling glass that has a dried layer of glue. Goggles, gloves, aprons are the minimum precautions against the slivers of glass.
Friday, 12 September 2008
Glue Chipping, 4
Applying the glue
The glass should be clean and have a dam around it.
Cleaning the glass is important. If there is dust left from the sandblasting/grinding stage, the glue will not stick to the glass.
Place the glass on a level surface. The glass should be room temperature.
Pour the glue onto the glass in an even layer between 1mm to 3mm thick. If the glass is level the glue will flow to a uniform thickness on its own. You can tilt the glass from side to side to help the glue flow.
CAUTION: If your glue is too hot, it may shock the glass causing it to break, allowing the glue to run all over the place. Another reason to avoid heating the glue to a high temperature.
The glass should be clean and have a dam around it.
Cleaning the glass is important. If there is dust left from the sandblasting/grinding stage, the glue will not stick to the glass.
Place the glass on a level surface. The glass should be room temperature.
Pour the glue onto the glass in an even layer between 1mm to 3mm thick. If the glass is level the glue will flow to a uniform thickness on its own. You can tilt the glass from side to side to help the glue flow.
CAUTION: If your glue is too hot, it may shock the glass causing it to break, allowing the glue to run all over the place. Another reason to avoid heating the glue to a high temperature.
Thursday, 11 September 2008
Glue Chipping, 3
Mixing the Glue
The 'type' or 'pattern' of desired chip design is dependent upon the glue to water ratio.
Generally the dry glue is combined with COLD water in a ratio of 3 parts water, 1 part glue. This is measured by WEIGHT - 1 oz. of glue to 3 oz. of COLD water per sq. ft. of glass. If your glass is 24"x24", this is 4 sq. ft. so you will need 4 oz. of DRY glue and 12 oz. of cold water.
Using metric measurements is easier when combining wet and dry materials by weight. 1 litre of water is 1 kg. So for 0.1 sq. metre (approximately 1 sq. foot) of glass you need 25 grams of glue to 75 cl of water.
After mixing let this mixture stand for about 1 hour to absorb all the liquid. It also helps to cover this container to reduce evaporation. This mixture will form a gelatinous mass.
Average Recipe:1 to 2 ounces of Dry Glue per sq. ft.
3 ounces of COLD water per sq. ft.
OR
285 to 570 grams of dry glue per square metre
850 centilitres of Cold water per square metre
Heat this mixture in the double boiler. Do not try to heat the glue container directly on a burner. This will stink tremendously. Slowly heat this mixture to 60 – 65C (140 - 150 F). It is important that you do not boil this mixture and that is stays between these temperatures. Use a sugar/candy thermometer to measure the temperature of glue. Stir occasionally. Heat slowly.
The 'type' or 'pattern' of desired chip design is dependent upon the glue to water ratio.
Generally the dry glue is combined with COLD water in a ratio of 3 parts water, 1 part glue. This is measured by WEIGHT - 1 oz. of glue to 3 oz. of COLD water per sq. ft. of glass. If your glass is 24"x24", this is 4 sq. ft. so you will need 4 oz. of DRY glue and 12 oz. of cold water.
Using metric measurements is easier when combining wet and dry materials by weight. 1 litre of water is 1 kg. So for 0.1 sq. metre (approximately 1 sq. foot) of glass you need 25 grams of glue to 75 cl of water.
After mixing let this mixture stand for about 1 hour to absorb all the liquid. It also helps to cover this container to reduce evaporation. This mixture will form a gelatinous mass.
Average Recipe:1 to 2 ounces of Dry Glue per sq. ft.
3 ounces of COLD water per sq. ft.
OR
285 to 570 grams of dry glue per square metre
850 centilitres of Cold water per square metre
Heat this mixture in the double boiler. Do not try to heat the glue container directly on a burner. This will stink tremendously. Slowly heat this mixture to 60 – 65C (140 - 150 F). It is important that you do not boil this mixture and that is stays between these temperatures. Use a sugar/candy thermometer to measure the temperature of glue. Stir occasionally. Heat slowly.
Wednesday, 10 September 2008
Glue Chipping, 2
Preparing the glass
The surface of the glass must be roughened up to allow the glue to adhere to the glass. This roughening is most often done by sandblasting the area of glass to be chipped. It can also be done by grinding the glass with grit between the glass to be chipped and another hand-held piece of glass. The grit should be at least 100 grit, and coarser is better.
After this roughening is done clean the glass thoroughly. Use raised masking tape to create a dam around the edge of your glass. This will keep the glue from flowing over the sides of the glass.
The surface of the glass must be roughened up to allow the glue to adhere to the glass. This roughening is most often done by sandblasting the area of glass to be chipped. It can also be done by grinding the glass with grit between the glass to be chipped and another hand-held piece of glass. The grit should be at least 100 grit, and coarser is better.
After this roughening is done clean the glass thoroughly. Use raised masking tape to create a dam around the edge of your glass. This will keep the glue from flowing over the sides of the glass.
Tuesday, 9 September 2008
Glue Chipping, 1
Glue Chipping Glass is easier than you might think. All that's needed are a few materials and a little experimenting. You can chip on a variety of glasses such as clear, coloured cathedral or flashed glass. You can also chip bottles, jars and even mirrors.
The glue used for chipping glass is animal hide glue or "glass chipping glue" and can be purchased through most stained glass retailers and art shops. It should be granular and is usually sold by the pound. One kilogram will generally chip up to 2 square metres.
The basic steps are:
The glue used for chipping glass is animal hide glue or "glass chipping glue" and can be purchased through most stained glass retailers and art shops. It should be granular and is usually sold by the pound. One kilogram will generally chip up to 2 square metres.
The basic steps are:
- Prepare Glass
- Mix glue
- Apply glue
- Let dry
- Clean with warm water
Subscribe to:
Posts (Atom)