Scoring Glass

Cutting glass is done by “scoring” the surface of the glass with a glass cutter, then breaking it along the score line. The break you make will always follow the path of least resistance, so you want to be sure that the score you make becomes that easy path and glass breaks the way you want it to.

Holding the Cutter
Generally, you use the cutter by moving it away from you, so you can see the cartoon lines as you score. When using a straight edge such as a cork-backed ruler to guide your cutter, you can pull the cutter toward you, or push it away as suits you. The cutter should always be held at a 90 degree angle (left to right). You can determine this by looking down the cutter to the wheel and to the cartoon line below.

It is important that the work be done from the forearm rather than the fingers or the wrist. The forearm should be held closely to the body. This reduces the freedom of movement, giving clean flowing score lines. It also reduces the actions that can lead to repetitive stress injuries. Any turning required by tight curves can be done by turning the body from the hips or shuffling around the bench with the glass at a corner.  Of course, for long cuts your arm will have to extend from you body in a parallel direction with the score line.

Scoring Pressure
The second and very important element in scoring glass is the amount of pressure used.  Very little pressure is required.  You should hear no more than a quiet hiss on transparent glass and almost no sound on opalescent glass.  However some manufacturer's transparent glass has almost no sound either.  So the important element is the pressure, not the sound.   Most people start with applying far too much pressure. Tests have shown that only about 2 kg of pressure is required for a clean score.

You can test the effect of this amount of pressure on a bathroom scale.  Place a piece of clear glass on the scale and without touching the glass with your other hand, score it noticing how much weight is being recorded.  Keep trying until you are at the 2 kg area of pressure.  Try breaking the glass.  Score a curve with the original amount of pressure and break the glass.  Then using the same curve score the glass with the 2 kg pressure and break the glass.  You will see and feel the lesser pressure provides a clean break.

Excessive pressure leads to breaks showing significant stress marks on the edge of the glass.  Too little pressure has no effect on the glass, making it impossible to break along the score line.  The correct pressure (ca. 2 kg.) leads to almost vertical stresses being put into the glass which assists the breaking along the score line.  Too heavy pressure creates stress marks which are at increasingly large angles with the increasing pressure.  This will still break cleanly on straight lines, but when working around curves the glass can follow one of the lateral stress marks away from the score line.  Excessive pressure is often the cause of glass breaking away from the score line on a curve, especially a tight one.

Foiling Nuggets

Grinding of the edges of the nuggets is not required for foiling. Roughing up the surface helps some adhesives hold better, but it depends on the viscosity of the adhesive and the degree of "roughness" of the surface. The adhesive on copper foil sticks better to a smooth than a rough surface. Try sticking it both to glass and to fine sandpaper and see which is easier to scrape off, for example. You will find the foil easily comes off the sandpaper, which is the texture of the surface you leave when grinding.

So you do not need to grind. You may need to wash them with soap and water to remove any oil that may be on the surface to ensure a good contact, however. Just put the foil on the clean nuggets. Then put a bunch of the foiled nuggets in a plastic container and shake around until all the nuggets are nicely burnished.

Check each one to ensure they are fully burnished to the nugget. Smooth any lifted parts of the foil with a fid and they are ready for soldering.

Glass Stuck to Moulds

Glass that is stuck to moulds needs more care in removal than removal of glass from kiln shelves does.

The major element in removal is to get the mould to release the glass. This requires some diagnosis of why the glass is stuck.

• Is the glass trapping the mould? This happens most often when the glass is draped, especially over ceramic moulds.
• Has the glass been fired high enough to fuse to the mould? If you have fired the glass to tack fusing temperatures, you may find more occasions when the glass sticks slightly or firmly to the mould.
• Is the mould trapping the glass? This can happen when slumping into a steep sided steel mould. Occasionally a steep sided ceramic mould will show the same effect.
• Has the separator been too thin or failed? If none of the previous elements apply, it may be that the separator was too thin or has been fired to tack fusing temperatures in a previous firing.

You can use mechanical methods to free the glass from the mould by inserting a thin pallet knife between the glass and the mould. This works better for items where the glass is inside the mould. If the glass is outside the mould, the chances are that you will break the glass. Using mechanical methods for any glass that is more than lightly stuck will most often lead to breakage of the glass, and often both items.

Where the mould is trapping the glass, you can put the item back into the kiln, but upside down and supported a centimetre or so above the kiln shelf. Heat the glass gently toward slumping temperatures. The glass should fall from the mould at 300 or 400C, but you need to keep watch to make sure you do not over heat the glass.

Where the glass is trapping the mould and you are using mechanical methods, you normally need to decide which is more important – the mould or the glass. It is just possible to break a ceramic mould and leave the glass, if the glass is 6mm or more. If the mould is more indestructible, you will probably lose the glass.

With ceramic moulds you can try heating the two to 300C or 400C and reach in with appropriate protection to try to lift the mould out of the glass. If the mould is steel, it will expand faster than the glass and break it.

Once you have the glass off, you may need to repair the mould.

Aperture Drops Finishing

After the piece has cooled and been removed from its ring, you can consider how to finish the piece.  The first decision is whether to retain or remove the rim from the vessel. In some cases, the rim can be retained as an integral part of the piece and there is little work needed to finish the piece.  Possibly only tidying up the edge of the rim and cleaning the bottom.

Removing the rim

But for most aperture drops and for most people, it is desirable to remove the rim. To have successful drops without rims, you most often need to have access to cutting and polishing equipment.  There are several ways to do this. 

The method that uses least equipment is to score around the upside down drop just above the rim.  When scored, tap the rim with a soft hammer to release it.  This is not always an even break and sometimes runs into the length of the drop.

A low tech way of cutting is to put a diamond cutting blade on a Dremel-like battery powered tool and with a flow of water grind through the side of the drop.  It is best to have a small flow of water directed at the cutting area, rather than immersing the rim in a bath of water.  This helps avoid electrical shock.

The rim can be cut off in portions with a tile saw, cutting quarters, eighths, sixteenths off the rim, approaching the edge of the drop.  Those with adjustable height wet saws can cut through small portions at a time of the rim, and support both the rim and the drop, especially when nearing the completion of the cuts.

There are also specialised versions of the wet angle grinder that make cutting of the rim easy and much more certain of a good result.

Finishing

After any of these methods of removing the rim, the drop edge, and possibly bottom, needs to be ground and polished.  Fire polishing is not possible as the drop would collapse long before the rim was smooth.

Because the rim will be relatively thin, it is possible to grind and polish with hand pads.  However, it is quicker to use a flat lap or linisher with a succession of finer grits to grind and polish an edge.  HIS Glassworks has a series of videos and this one gives good information on the methods and progression of grits to get to a polished edge whether by machine or by hand.

Aperture Drops Annealing

The soak at annealing temperature will need to long to accommodate the temperature variations within the thick and thin parts. The thin parts will be able to cool much faster than the thicker parts.

The objective in annealing is to keep all parts of the glass cooling within a 5C range, so the soak will need to accommodate those differences. I suggest a minimum soak time is 90 minutes for a 9mm thick blank, 2 hours for 12mm and 3 hours for a 15mm blank to be certain all the glass reaches the same temperature.

Annealing the drop has two main considerations – the variation in temperature over the length of the piece and the variation of thickness of the glass. These two in combination make it difficult to find a rapid annealing and cooling schedule. So having spent quite a bit of time so far on the piece, choosing a conservative schedule is sensible.

The variation in temperature between the top and bottom of the kiln can vary quite a bit, maybe as much as 20C for some kilns. So you can see immediately that the annealing will need to be slow if you are going to keep the thick and thin glass within 5C of each other. It would be possible to use schedules for annealing thick pieces just as they are published for the thickness of your blank, but it is more conservative to use a cooling schedule for the next size up to ensure a good anneal.

Thus, for a 9mm piece I would anneal at 55C/hr for the first 55C below annealing, then 99C/hr for then next 55C. After that you can go much faster. For a 12mm piece I would go at 25C/hr for the first 55C, 45C/hr for the next 55C and 150C/hr to room temperature. For a 15mm piece I would go at 15C/hr for the first 55C, 27C/hr for then next 55C, and 90/hr to room temperature.

It may be possible to go faster than this in annealing, but this is cautious to make sure the variations in both thickness and temperature are considered.

Aperture Drops - Stopping the Drop

Arresting the drop and cooling the piece can be complicated, as you need to cool the kiln quickly enough to stop the glass moving.

The higher the forming temperature of of the work, the quicker you need to stop the movement of the glass. This will involve opening the kiln to cool the glass enough so that it becomes stiff and resists further movement. You need to be aware that you are cooling glass that ranges in thickness from relatively thick to relatively thin. The thin parts will cool faster than the thick parts. Flash cooling for too long will make the thin parts very stiff, while the thicker part are still hot. This could lead to breakage if allowed to continue down to the annealing soak temperature.

A lower forming temperature will allow you to simply advance to the rapid cool portion of the schedule down to the annealing soak without the need for flash cooling. You do need to make this skip to the next segment just a minute or so before the piece reaches its desired length or shape. This will not be difficult to judge as you will have been checking frequently at this portion of the firing.

Aperture Drop Observation

This kind of firing absolutely requires observation of the progress of the drop. Ideally you would set up the firing surface where you can peek at it during the firing as well as observe the bottom of the kiln or the shelf – which ever you are firing upon.

I you have to choose, then the bottom of the kiln is the most important place to have clear observation lines. Even if you do not want the drop to touch the shelf or bottom of the kiln, you will need to observe how far the drop has progressed.

Thus, planing for the placing of the supports and other elements of the drop are important. Support posts should not obscure the view of the drop, for example. The whole set up should be placed far enough back in the kiln to see the shelf/kiln bottom where the glass will touch down.

If you do not want to have the drop touch down onto a surface, you need to set up a “witness” to indicate how far the glass has fallen. This can be some pieces of fibre stacked up so that your view through the peep hole to the top visible surface of the “witness” will tell you that when the glass touches that line of vision, it has reached the desired length.

You need to patient, as the soaks can be two or more hours long for a low temperature drop.

Aperture Drop Placement

Aperture drops normally are placed much higher in the kiln than most work to get the greatest length of drop. This means that the glass is near the elements and so will be heated unevenly. It has been said that the heat evens out across the kiln approximately the distance below the elements that they are apart. So if the elements are 100mm apart, the heat will even 100mm below the elements. This constraint means that it is difficult to get the length of drop wanted and still have the glass heat evenly.

There are at least two things you can do to get more height. One is to take out the shelf and its supports so you can fire on the bottom of the kiln. This will give up to 50mm extra drop length.

The other is to go ahead and fire closer to the elements than is indicated for even heating. This will require radical modification of the heating schedules. [qv firing]

Grinder Head Grub Screw

Need help! The small screw that secures the grinder bit to the shaft was stuck and my efforts to loosen it resulted in stripping it. I've tried spraying it with lubricant -- still no luck. What can I do?

There is a tool that many mechanics and tool shops have. It is normally square or triangular. It is used by drilling into the broken off bolt, or in this case, the grub screw. The tool is hammered into the hole and then with a wrench/spanner loosened.

However, you should make sure that the socket for the allan key is clear of glass residues. I do this by using a needle or other thin sharp object to clear out all the glass powder. I am sure there are other things to clean out the hole too. When the socket is cleaned, I push the key into the socket very firmly and hold it there while turning. This has worked for me in the past.

Once the grub screw is out, you need to get a replacement, so the same problem does not re-occur. I keep the screws from old heads in my box of grinder parts for this eventuality.

So the maintenance is not only on the shaft but also on the fixings. Putting a dab of Vaseline or thick grease into the socket will help keep it clear of the glass residue.

Aperture Drops Firings

Initial Heat Rise

As the placement of aperture drops is much higher in the kiln than normal, the initial heat rise needs to be carefully controlled. Usually, the glass will be so high in the kiln that uneven heating is almost certain and the risk of breakage very high. The need is to arrange a schedule that takes account of this uneven heating effect.

The principle requirement is to add heat slowly so the glass receiving less direct heat can heat up by convection through the glass. However glass is a very good insulator, allowing heat to travel only slowly. There are two strategies for this:

• one is to heat at a very slow but consistent rate. After the annealing point has been reached the speed can be increased.
• the second is to go a bit faster, but with soaks at three or more intervals in the heat up. After each soak the speed of advance can be increased a little. The soaks should be from 15 to 30 minutes, depending on the speed of heat up.

In either case it should take about five to six hours to reach 650C for 9mm thick glass. If the glass is thicker, more time is required to get to this point. I would take 8 -9 hours for 12mm glass; 16 – 18 hours for 15mm glass; 26 – 30 hours for 18mm glass.

Bubble Squeeze

If the glass has not already been fused, you may need a bubble squeeze at around 650C. Keep in mind that the temperature rise has been slow and so a lot of heat has been put into the glass. A quick peek can tell you whether the glass has already sealed at the edges. If the glass was per-fused, you can continue directly to the forming temperature.

Forming temperature

The exact forming temperature of course is dependent on:

• aperture size
• weight of glass
• speed of advance to forming temperature
• glass used (to a lesser extent)

However the forming temperature will be between a high temperature slump and a low temperature fire polish or tack fuse. Observation will be required to determine the temperature for your kiln.

Soak at forming temperature

It is best to soak for a long time at the forming temperature. At high temperatures the glass will move quickly, possibly too quickly to arrest the movement when you want. At higher temperatures the glass thins much more at the shoulder – where the glass moves from the horizontal to the vertical – than at lower temperatures.

Lower temperatures take longer to form, but are more controllable. More of the glass has time to slip into the aperture. Lower temperatures allow compensation for the increased speed of the drop during long drops. After the first 50-75mm of drop the glass at the sides is thin enough to allow a quicker drop caused by the weight of glass at the bottom pulling on the thinner sides.