Creating a Quality Solder Joint

Soldering is the process that uses solder (a metal alloy usually consisting of tin mixed with other metals) for the metallurgical joining of metal components to form an electrical, mechanical or hermetically sealed bond at temperatures (less than 449°C) that are well below the melting temperature of the individual components that are being joined. The soldering equipment (used to create the required heat) and other materials (solder, fluxes, heat sinks, fixtures, etc.) should always be properly matched to the intended soldering application. The equipment and materials used may vary, but the basic soldering techniques that are required will usually remain the same.

One of the most important rules to remember about soldering is "keep it clean". This includes, not only the items being soldered, but also the materials used. Choose quality solders and fluxes without unnecessary impurities. Surface oxidation, contaminants and other impurities are some of the most common reasons for poor quality solder joints. The use of fluxes does not eliminate the need for pre-cleaning the surfaces you are joining, especially if heavy oxidation or large amounts of grease, oil or dirt are present.

1. Clean: Thoroughly clean all surfaces to be joined, removing any dirt, grease, oil, oxidation, paint, coatings or other impurities that may exist before attempting to solder. Proper wetting can only occur when the intended solder joint area has been properly cleaned. Soldering should be performed as soon as possible after cleaning to eliminate the possibility of re oxidation or contamination of the items being soldered. [So leaving pieces fluxed overnight is not good practice. Flux only the area that can be soldered in the next few minutes.]

2. Flux: Apply flux sparingly to each of the intended joint surfaces. Flux is primarily used for the removal of light oxidation and to protect against re-oxidation during the actual soldering process. Make sure you have the right flux for the application being performed.

3. Heat: Apply heat directly to the intended joint area. The correct application of heat is important and should be consistent with the operating requirements determined by the type of equipment being used. Fast and accurate heating will minimize the risk of thermal damage.

4. Solder: Add solder to the heated surfaces you are joining (do not apply solder directly to the tip, or other heat source being used). The solder should flow uniformly over all of the surfaces that are being connected. Stop feeding solder as soon as you have applied an adequate amount and then remove the heat source. The amount of solder is important because too much will create unnecessary waste, while too little can affect the mechanical strength and conductivity of the finished solder joint.

5. Cool: Allow the finished solder joint to remain undisturbed until it has completely cooled. You should never attempt to speed up the cooling process by blowing on the solder joint. Even minor vibrations or disturbances during cooling, can cause micro fractures or other types of damage that may severely weaken the solder joint.

6. Inspect: Check all finished joints for proper wetting, the right amount of solder, a good physical appearance, and the required mechanical strength.

SkillsA quality solder joint is not achieved solely by the equipment and techniques being used, but also by the operator being trained to use them properly. An operator should know how the physical appearance of a finished solder joint helps to determine possible flaws that may exist.

A quality solder joint appears bright, shiny and smooth with all components appearing well soldered. The surface of a finished connection should never look rough, grainy, dull, or flaky (these are signs of what is commonly referred to as a cold solder joint). Problems with proper wetting (solder balling up and not adhering to the components surface) are sometimes associated with too much heat, but are more often related to cleanliness issues.

Courtesy of American Beauty Tools

Soldering Ingredients and Methods

The soldering process may be accomplished in a wide variety of ways, but the four primary ingredients required will remain the same. They are; the base metal (or metal items being joined) a type of flux (or a method of cleaning and maintaining the surface to be soldered), the solder and a source of heat. It is important to match the soldering method and the equipment that will be used, to the soldering application that is being considered.

Base MetalThe base metal is the metal that is in contact with the solder and forms an intermediate alloy. There are many metals that will react willingly with solders to form a strong chemical and physical bond, while others can be very difficult, or even impossible to solder.

Flux
Flux is used to eliminate minor surface oxidation and to prevent further oxidation of the base metals surface during the heating process. Although there are many types of flux, each will include two basic parts, chemicals and solvents. The chemical includes the active portion, while the solvent is actually the carrying agent. It is the solvent that determines the cleaning method required to remove the remaining residue after soldering.

Solder
Solder is the alloy used to create the solvent action, which generates the bond between the base metals. The type and form of the solder is very important and must be determined by the individual application being performed, as well as the base metals and soldering method being employed.

Methods
There are several methods, as well as a wide variety of tools available to perform the task of soldering. Some of the current methods that are available include induction, conduction, ultrasonic, flame, dipping, resistance, oven and wave soldering. Some of these methods involve the use of small inexpensive hand tools, while others may require large and expensive machinery, equipment and tools. It is a good idea to become educated on the various methods and tools that are available, in order to insure that you are utilizing the best, safest, most efficient and economical means available for your specific soldering application.

Courtesy of American Beauty Tools

Soldering vs. Welding

The metal joining process that is generally referred to as soldering (or soft soldering) requires temperatures between 183 to 445°C. The joining of metals at temperatures above 445°C (and below the melting point of the metals being joined) is more commonly referred to as brazing (or hard soldering). The actual melting and fusing of the metal items that are being joined together is considered welding. There are, of course overlapping situations that may occur when classifying a process.

The actual joining characteristics that take place are physically different in each of these processes. Soft solders attach to metals by what is referred to as a solvent action that takes place at relatively low temperatures. Hard solders, or brazing alloys contain metals that require higher temperatures to cause the solvent action to take place and fuse the alloy with the metal being joined. Because welding involves actually melting and fusing the surface of the metals that are being joined together, a filler, or fusible material is not always used.

Courtesy of American Beauty Tools

Soldering - how it works

Soldering is a well known and widely used process where two or more metal items are joined together using a fusible alloy with a melting temperature that is lower than their own. The most commonly used solder is a fusible alloy consisting essentially of a tin and lead mixture.

The solder actually dissolves a small amount of the metal’s surface, at a temperature that is well below its melting point and joins with it. It is this solvent action of the solder alloy that causes it to fuse with and attach to the surface of the metal items being joined.

The solvent action that takes place, between the solder and the metal, makes the joint chemical (not just physical) in nature and causes the properties of the joint to differ from the original solder’s properties and from those of the surface of the metal items being joined. When metal parts are joined by solder, a metallic continuity is established as a result of the interfaces where the solder is bonded to the metallic surfaces.

Courtesy of American Beauty Tools

Maintenance of Soldering Bits -Periodic Cleaning

It is important to periodically clean the shank of the plug style bits as well as the inner surface of the element. This is done to keep the bit from seizing in the element and also to keep from building a layer of oxides and contaminates that would obstruct the transfer of heat from the element to the bit. After allowing the iron to completely cool the bit should be removed and the bit shank and inner walls of the element should be wiped clean with a mildly abrasive emery cloth or soft wire brush. This cleaning process should be done as often as needed, depending on the work environment, but not less than once a week.

Courtesy of American Beauty Tools

Other links to Soldering Iron Maintenance:
https://glasstips.blogspot.com/2019/11/soldering-iron-maintenance.html

https://glasstips.blogspot.com/2010/01/maintenance-of-soldering-bits-periodic.html

https://glasstips.blogspot.com/2009/12/soldering-bit-maintenance-wiping-bit.html

https://glasstips.blogspot.com/2009/12/soldering-bit-maintenance-tinning.html

Soldering Bit Maintenance - Wiping the Bit

During use a bright, thin, but evenly tinned surface must be maintained on the working portion of the bit. Oxidation and contaminants must be continually removed from the bit surface to achieve maximum performance. This will help to ensure the proper transfer of heat from bit to work and will eliminate the possibility of impurities being transferred into the solder joint.

Between each solder application simply wipe the working area of the bit clean on a damp cellulose sponge to remove the dross and oxides that will accumulate and add small amounts of fresh solder to the bit as needed. A gentle wiping is all that is required and care must be taken not to over wipe the bit, because oxidation will occur on the surface quite rapidly if all of the solder has been removed. Once this oxidation occurs it becomes difficult, or even impossible for solder to wet to the bit. It then becomes necessary to properly clean and re-tin the bit in order to regain the appropriate wetting action required for adequate performance. When you have finished the soldering application, you should wipe any contaminates from the bits surface and add a small amount of fresh solder to it before allowing the iron to cool. This layer of solder ensures protection from oxidation of the bit between uses and will help to extend the bits working life.

Courtesy of American Beauty Tools

Other links to Soldering Iron Maintenance:
https://glasstips.blogspot.com/2019/11/soldering-iron-maintenance.html

https://glasstips.blogspot.com/2010/01/maintenance-of-soldering-bits-periodic.html

https://glasstips.blogspot.com/2009/12/soldering-bit-maintenance-wiping-bit.html

https://glasstips.blogspot.com/2009/12/soldering-bit-maintenance-tinning.html

Soldering Bit Maintenance - Tinning

Introduction
Proper care and maintenance of your soldering iron bit involves tinning, wiping (and wetting) and also periodic cleaning of the bits shank. These actions are very important and quite simple to perform, but are often neglected. When performed properly they will not only ensure the longest possible working life for your soldering iron bits, but they will also have positive effects on the overall performance of your soldering iron.

TinningTinning may not be necessary if the bit you are using is new and arrives pre-tinned from the manufacturer, or has been used previously and been properly maintained. When a bit does need to be tinned (or re-tinned) it must be clean and free of any surface oxidation before it will accept any solder. Once the bit is properly tinned, care should be taken to prevent bit de-wetting by occasionally cleaning and adding small amounts of fresh solder, especially if the bit is being subjected to long periods of inactivity or idling.

If the bit to be tinned is un-plated copper it should be cleaned and dressed with a single cut, flat file. After filing the bit it should be heated in the iron. When the bit reaches the lowest temperature required to melt solder, a rosin core solder should be fed onto the bit. Do not allow the iron temperature to rise too high before applying the solder, because excess heat will cause the bit surface to re-oxidize and no longer accept the solder.

If the bit is plated it should never be filed, or heavily abraded. Care should be taken to ensure the plating is not damaged or removed, as this will shorten the working life of the bit dramatically. When pre-cleaning is necessary for plated bits, they should be cleaned with a mildly abrasive emery cloth and may require an acid flux to remove the oxides before tinning, or re-tinning.

Courtesy of American Beauty Tools

Other links to Soldering Iron Maintenance:
https://glasstips.blogspot.com/2019/11/soldering-iron-maintenance.html

https://glasstips.blogspot.com/2010/01/maintenance-of-soldering-bits-periodic.html

https://glasstips.blogspot.com/2009/12/soldering-bit-maintenance-wiping-bit.html

https://glasstips.blogspot.com/2009/12/soldering-bit-maintenance-tinning.html

Soldering Bit Maintenance - Summary

If a bit has not been properly tinned, solder will not wet to it. Without solder on the bit heat transfer from the bit to the work surface may become extremely difficult and time consuming, or even impossible.

You must understand that proper wiping and continuous wetting is important and a lot easier than continually having to clean and re-tin the bit, especially at the risk of damage to the plated surface because of accidentally scratching, or over abrading it.

When you notice that an iron is not performing as well as it did when it was new you will find that poor thermal transfer from the element to the work is usually the cause. Improper care and maintenance and the lack of a periodic cleaning of the bits shank can cause a layer of oxides, which will inhibit the transfer of heat through the bit. Always ensure plug style bits are properly seated into the elements before heating the iron. If a bit is not inserted fully into the element there may be a gap behind the bit. This gap can cause a hot spot within the element causing a premature failure of the soldering iron.

Courtesy of American Beauty Tools


Other links to Soldering Iron Maintenance:
https://glasstips.blogspot.com/2019/11/soldering-iron-maintenance.html

https://glasstips.blogspot.com/2010/01/maintenance-of-soldering-bits-periodic.html

https://glasstips.blogspot.com/2009/12/soldering-bit-maintenance-wiping-bit.html

https://glasstips.blogspot.com/2009/12/soldering-bit-maintenance-tinning.html

Choosing the Soldering Bit

An important consideration, when choosing the most appropriate bit, is that thick, short bits will store more heat and deliver it more efficiently than long, narrow ones. This makes the standard chisel configuration the usual bit of choice. The chisel shaped bit is often used for joining flat seems together. The working edge of the chisel bit should be about the same width as (or slightly wider than) the seam that is being soldered.

Usually a solder connection is made in one to three seconds. If the connection takes longer than three seconds, you may need a larger bit, a higher wattage iron or a completely different type of soldering equipment altogether. It is a good idea to familiarize yourself with other soldering methods and equipment that are available in order to ensure that you are utilizing the best, safest, most efficient and economical means available to perform your soldering application.

Courtesy of American Beauty Tools

Soldering Bits

Type
The bit type is determined by the soldering iron it is used on. There are screw type bits (bits that screw onto, or into the solder iron element), slip on bits that slip over the element and plug type bits that slide inside of the element. There are even bits that are a permanent part of a replaceable element/bit assembly. Regardless of the type of bits required it is always important to have them fully seated to the element and periodically cleaned, in order to maintain proper heat transfer from the element into the bit.

ConfigurationThe bit configuration to use should be determined by the intended application requirements. Some of the basic bit configurations available include ballpoint, conical, diamond (pyramid), chisel, and spade. You will find that there are usually a variety of styles, or modifications available, within each of these basic configuration families, to accommodate specific application requirements. Although less efficient, a more narrow configuration is sometimes required to obtain accessibility, or to achieve the desired results.

SizeThe bit size to use (regarding the working portion) should also be determined by the intended application requirements. The bit body, or shank must be matched to the iron it will be used with (always select a bit that was designed, or approved for the soldering iron you intend to use on the application being considered). As with bit configuration though, there are usually a variety of modified working diameters available within each family of standard bit sizes that are available. These modified bits are generally referred to as turned down bits, because the working area of the bit has been turned down to a smaller diameter than the body, or shank diameter. Turned down bits are not as efficient, but are sometimes required to solder in otherwise inaccessible areas.

Courtesy American Beauty Tools