Even Solder Beads

Getting even solder beads is a lot about where you look while you solder. Unlike drawing or cycling looking at where you are going is not so useful when soldering. You need to see the effects of what you are doing so looking behind the solder bit will help you understand what you are doing. If the bead begins to get small or narrow you either slow down the forward movement of the solder bit or add solder to it more quickly. If the bead begins to get too thick, you do the opposite. You can move the bit faster, or reduce the speed of feeding the solder to the bit.

Another element in getting an even bead is the heat being delivered. If you use a wide soldering bit you are delivering more heat to the joint. You hold the chisel bit so that it runs along the foil. The bigger the bit, the more heat is being held. And the more heat held in the bit, the more heat is applied to the soldering. Small bits are for getting into tight spots and for decorative soldering. Big wide bits are best for running beads.

Plaster Properties - Effect of Plaster-Water Ratio

Plaster-water ratio (by weight) of 100 plaster to 30 water gives:
a setting time of 1.75 mins,
a compression strength of 813 kg/sq cm., and
a density of 1806 kg/cubic metre

Plaster-water ratio (by weight) of 100 plaster to 40 water gives
a setting time of 3.25 mins,
a compression strength of 477 kg/sq cm., and
a density of 1548 kg/cubic metre

Plaster-water ratio (by weight) of 100 plaster to 50 water gives
a setting time of 5.25 mins,
a compression strength of 318 kg/sq cm., and
a density of 1352 kg/cubic metre

Plaster-water ratio (by weight) of 100 plaster to 60 water gives
a setting time of 7.24 mins,
a compression strength of 230kg/sq cm., and
a density of 1207 kg/cubic metre

Plaster-water ratio (by weight) of 100 plaster to 70 water gives
a setting time of 8.75 mins,
a compression strength of 176 kg/sq cm., and
a density of 1083 kg/cubic metre

Plaster-water ratio (by weight) of 100 plaster to 80 water gives
a setting time of 10.5 mins,
a compression strength of 127 kg/sq cm., and
a density of 990 kg/cubic metre

Plaster-water ratio (by weight) of 100 plaster to 90 water gives
a setting time of 12 mins,
a compression strength of 99 kg/sq cm., and
a density of 908 kg/cubic metre

Plaster-water ratio (by weight) of 100 plaster to 100 water gives
a setting time of 13.75 mins,
a compression strength of 70 kg/sq cm., and
a density of 867 kg/cubic metre

Properties of Typical Gypsum Plasters and Cements

No. 1 pottery plaster
Water to be added as % of dry mix by weight - 70%
Setting time - 27-37 mins
Dry density (kg/cubic metre) - 1106
% expansion on setting - 0.21
Compressive strength (kg/sq cm) - 127.26


No. 1 molding plaster
Water to be added as % of dry mix by weight - 70%
Setting time - 27-37 mins
Dry density (kg/cubic metre) - 1106
% expansion on setting - 0.20
Compressive strength (kg/sq cm) - 141

Plaster of Paris
Water to be added as % of dry mix by weight - 70%
Setting time - 27-37 mins
Dry density (kg/cubic metre) - 1106
% expansion on setting - 0.20
Compressive strength (kg/sq cm) - 141

No. 1 Casting plaster
Water to be added as % of dry mix by weight - 65%
Setting time - 27-37 mins
Dry density (kg/cubic metre) - 1162
% expansion on setting - 0.22
Compressive strength (kg/sq cm) - 170

Pottery plaster
Water to be added as % of dry mix by weight - 74%
Setting time - 27-37 mins
Dry density (kg/cubic metre) - 1057
% expansion on setting - 0.19
Compressive strength (kg/sq cm) - 127

Hydrocal cement
Water to be added as % of dry mix by weight - 45%
Setting time - 25-35 mins
Dry density (kg/cubic metre) - 1442
% expansion on setting - 0.39
Compressive strength (kg/sq cm) - 35

Hydroperm cement
Water to be added as % of dry mix by weight - 10%
Setting time - 12-19 mins
Dry density (kg/cubic metre) - <641
% expansion on setting - 0.14
Compressive strength (kg/sq cm) -


Hydro-Stone cement
Water to be added as % of dry mix by weight - 32%
Setting time - 17-20 mins
Dry density (kg/cubic metre) - 1914
% expansion on setting - 0.24
Compressive strength (kg/sq cm) - 707

Ultracal cement (30)
Water to be added as % of dry mix by weight - 38%
Setting time - 25-35 mins
Dry density (kg/cubic metre) - 1588
% expansion on setting - 0.08
Compressive strength (kg/sq cm) - 424

Solarisation

Old glass can show changes in colour as evidenced by the different colour of the glass under the lead came where the light cannot reach the glass.

Drew Anderson has provided the explanation.

This change in color of some glass is known as solarisation.

The main ingredient of most glasses is silica, which is usually introduced as a raw material in the form of sand. Silica itself is colorless in glass form but most sands contain iron as an impurity, and this gives a greenish tint to glass. By adding certain other ingredients to a molten glass, it is possible to change the greenish color and produce colorless glass.

These ingredients are known as decolorizers, and one of the most common is manganese dioxide (MnO2). In chemical terms, the manganese acts as an oxidizing agent and converts the iron from its reduced state - which is a strong greenish blue colorant - to an oxidized state which has a yellowish, but much less intense, color. In the course of the chemical reaction, the manganese goes into a chemically reduced state, which is virtually colorless.

When pieces of decolorized glass containing reduced manganese are exposed to ultraviolet radiation for long periods of time, the manganese may become photo-oxidized. This converts it back into an oxidized form. Even in low concentrations this imparts a pink or purplish color to glass. The ultraviolet rays of the sun can promote this process over a matter of a few years or decades.

Selenium and cerium have also occasionally been used as a decoloriser and can produce solarisation colors, just as manganese does. The colors developed by these two elements are said to range from yellow to amber.

Mesh Sizes from a Typical Manufacturer

Mesh sizes have traditionally been measured by the number of wires per square inch used to sieve the material. This table gives a grit size measurement for the mesh/grit numbers in common use.

Mesh = Mesh opening (mm)
12 =   1.5240
14 =   1.2954
20 =   0.8636
30 =   0.5156
40 =   0.3810
50 =   0.2794
60 =   0.2337
80 =   0.1778
100 = 0.1397
120 = 0.1168
200 = 0.0737
325 = 0.0432
400 = 0.037
625 = 0.020
1200=0.012
2500=0.005

Break-Down Temperature of Common Mould Binders

The temperatures that various binders used in mould making is important to consider, as once they reach the break down point, they lose their strength and therefore ability to hold the mould together. The following table gives some indication of the characteristics of various binders.

Binders and Break-down Temperatures (degrees C)
Gypsum plaster - 704 - 816
Hydrocal cement - 704 - 816
Hydroperm cement - 760 - 927
Colloidal silica - 1260
Colloidal alumina - 1260
Calcium alumina (ciment fondu) - 1538

These of course, are not the only considerations in mould making but do show why combinations of materials is important. The common plasters and cement break down before the casting temperature of glass, typically 850C.

Polishing 3D Glass on a Wet Belt Sander

Polishing three dimensional objects depends on the shape of the glass you are sanding down to the polished surface.

Convex shapes can be done on the wet belt sander with ease.

You can polish slightly concave items on a belt sander if you have an unsupported section of the belt. On machines with a flat platen, you can remove the platen to use the ability of the belt to form into a slightly convex curve.

Removing silicone

To remove silicone before it is cured you use a putty or other straight bladed knife to remove any of the uncured paste. Then wipe the area clean with isopropyl alcohol to remove any leftover residue.


After it is cured you should first you should remove as much of the silicone as you can with either a knife or a razor.

A solvent can them be used to remove any oily residue or any remaining silicone. It may be necessary to soak the silicone in a solvent overnight to break it down.

A list of solvents in the order of aggressiveness in attacking the silicone:
Paint thinner (mineral spirits)
Toluene
Xylene
Acetone
Methylene chloride.

When using solvents, as with any material, proper safety precautions should be observed. Material Safety Data sheets are available upon request from manufacturers. Similar information for solvents and other chemicals can be obtained from manufacturers.

There also are “Silicone Eaters” on the market now. The chemical composition is unknown, but are less messy and more expensive than some of the other solvents. Use according to instructions.

Glass Polishing Machines - Linisher

A wet belt sander, or linisher, is a machine intended to grind the edges of flat pieces of glass. It can do some work on bent, shaped, or slumped work, but its primary function is edging work while it is flat.

Table top model

The machines consist of a vertical or near vertical belt and a water supply to keep the belt and work lubricated and cool. Work generally starts with a low numbered grit belt, perhaps 80 grit, and then proceeds through the higher numbers. For example: 80, 120, 220, 400, 600, cork. Each stage should approximately half the grit of the previous one.

Floor standing model

Even with a cork belt, don’t expect a gloss you would see from a fire-polished piece. For that you need a cerium oxide belt or a felt belt with cerium oxide paste. Trizact is a brand name for fine polishing belts not requiring cerium oxide paste. These may be substituted for the more messy paste methods.

You can buy silicon carbide or diamond belts for a wet belt sander. The diamond belts are very expensive, but much longer lasting with proper care. If your belts are likely to receive rough treatment stick with the cheaper silicon carbide belts.

Cooling Events

This is based on Graham Stone’s work with float glass. The temperatures are applicable to float glass, and so need to be adjusted for a particular glass, but illustrate the principle of how heating temperatures affect the glass. Temperatures in degrees Celsius.


600 Common temperature for crash cooling toward. Glass beginning to "freeze".

555 Annealing temperature of float. Bungs in.

515 Approximate Strain Point of float.

535-400 Critical slow cooling down phase for float that overlaps annealing range.

400-300 Medium cooling down ramp rate.

300-10 Fast cooling down ramp rate. Cracking the kiln open possible.



Based on Firing Schedules for Glass; the Kiln Compainion, by Graham Stone, Melbourne, 2000, ISBN 0-646-39733-8, p24