Irregular rectangles
If you have found or can see that the opening is not a true rectangle and cannot determine where any right angles are, you need to take a template.
The objective is to make a piece that will fit into the opening without bending or being too small for the space. It will be the same size as the finished panel and so you will be able to put the finished panel into the opening without needing to trim or expand the panel.
First, trim the sheet of material you have chosen to use to a size a little larger than the measured size. Place the uncut side along one of the long sides of the opening. If the opening is a portrait format, place it on the right or left side as convenient to you.
Next, adjust the bottom by marking a line on the sheet. This is where a second person is very useful. One person can hold the sheet in place on outside of the opening and the other do the marking from the inside –in the case of the rebate being on the outside and vice versa if the rebate is on the inside. The marked line should be as close to the edge of the rebate as possible. The special case of an opening in stone will be dealt with separately.
Then take the sheet to a place where it can be safely cut. A long metal straight edge and craft or “Stanley” knife are often the best aids to cutting straight lines. Replace the sheet into the opening after cutting, and make any adjustments to the size and angles of the sheet at the bottom by marking and cutting as necessary.
When the side and bottom are adjusted, start on the other side. Proceed as for the bottom.
When the side is finished, start on the top.
Finally, present the whole sheet to the opening to make sure it slips into place with no snags, or bending of the sheet.
It may be that the opening is too large for a single sheet. In that case you will need to work with two or more sheets and try them together for the final fitting into the opening. You can put them together in the window. You can fasten them together with tape or other fasteners to make one sheet. You can also make two parallel lines both at angles and at intervals across the sheet so that when you get back to the studio you can exactly reproduce the full sheet by matching the marks and then firmly fastening them together. This makes transport of large templates much easier.
You will know that a panel made to a template made in this way will fit into the opening, no matter how irregular the opening may be.
Tuesday, 30 June 2009
Friday, 26 June 2009
Templates of Openings, 1
If you have an irregular opening, it may be best to take a tracing of the opening. Usually this will be in a larger opening and so a helper may be necessary to hold things.
The material used to take the template must have a few characteristics:
- It must be stiff enough to have the minimum possible bend over the width or height of the opening
- It must be easy to mark with a pencil or other implement
- It must be easy to cut or shape
- It should be light to make it easy to lift it to the opening for the many adjustments that will be required.
A number of materials can be used: stiff card, mounting board, corrugated cardboard, thin plywood, and many other sheet materials. I have found stiff corrugated cardboard easy to use.
More information in this series is at:
Irregular rectangles
Circles
Round headed windows
Irregular shapes
Stone
The material used to take the template must have a few characteristics:
- It must be stiff enough to have the minimum possible bend over the width or height of the opening
- It must be easy to mark with a pencil or other implement
- It must be easy to cut or shape
- It should be light to make it easy to lift it to the opening for the many adjustments that will be required.
A number of materials can be used: stiff card, mounting board, corrugated cardboard, thin plywood, and many other sheet materials. I have found stiff corrugated cardboard easy to use.
More information in this series is at:
Irregular rectangles
Circles
Round headed windows
Irregular shapes
Stone
Monday, 22 June 2009
Measuring a Rectangular Opening.
1 - Measure at both the top and bottom for width.
2 - Measure at the left and right sides for height.
If it is a tall or wide opening measure at intervals and at least in the middle of each side.
So far so good. But how do you know that it is a rectangle rather than a parallelogram? Measure the diagonals – bottom left to top right and top left to bottom right. If these measurements are equal or +/- 5mm you can consider the opening to be a rectangle.
With bigger variations you may set out the cartoon using the measurements for the opening. Still, you need to know where the right angles are, if there are any, to be able to set out the cartoon to properly fit the opening.
So you may wish to take a template of the opening.
2 - Measure at the left and right sides for height.
If it is a tall or wide opening measure at intervals and at least in the middle of each side.
So far so good. But how do you know that it is a rectangle rather than a parallelogram? Measure the diagonals – bottom left to top right and top left to bottom right. If these measurements are equal or +/- 5mm you can consider the opening to be a rectangle.
With bigger variations you may set out the cartoon using the measurements for the opening. Still, you need to know where the right angles are, if there are any, to be able to set out the cartoon to properly fit the opening.
So you may wish to take a template of the opening.
Saturday, 13 June 2009
Bulging lead panels
There is probably no means by which leaded glass, because of the innate character of lead as its skeleton, can resist its propensity to bend, bulge and sag. Evidence of these occurrences does not necessarily foretell disaster or immediate collapse. Bulging does not necessarily indicate the need for action or re-leading.
There are three basic stages through which stained glass passes on the way to requiring repair;
1. Bulging, bending and sagging
2. Loss of putty and breaking of solder joints
3. Unhousing of the glass from the lead
The points at which solder joints break depends on the materials used.
Since lead, compared with solder, is a resilient material abutting the more resistant solder, breaks will occur most frequently at the junction of the solder with the lead.
With zinc, the situation is reversed. The zinc is of greater resistance than the solder. As a result the break most often occurs on the solder at the point of the zinc junctions.
It is the very existence of resilience in lead which responds to the expansion and contraction of glass that permits the more healthy survival of the glass over the less sympathetic accommodations of either zinc or copper foil. Leaded glass, unlike any other medium, has the unique capability of having its skeleton (lead) replaced, when the need arises, without damaging its body (glass).
There are three basic stages through which stained glass passes on the way to requiring repair;
1. Bulging, bending and sagging
2. Loss of putty and breaking of solder joints
3. Unhousing of the glass from the lead
The points at which solder joints break depends on the materials used.
Since lead, compared with solder, is a resilient material abutting the more resistant solder, breaks will occur most frequently at the junction of the solder with the lead.
With zinc, the situation is reversed. The zinc is of greater resistance than the solder. As a result the break most often occurs on the solder at the point of the zinc junctions.
It is the very existence of resilience in lead which responds to the expansion and contraction of glass that permits the more healthy survival of the glass over the less sympathetic accommodations of either zinc or copper foil. Leaded glass, unlike any other medium, has the unique capability of having its skeleton (lead) replaced, when the need arises, without damaging its body (glass).
Wednesday, 10 June 2009
Combing Glass
This process is done at relatively high temperatures for fusers – around 925C. It consists of pulling or dragging the surface of the hot glass to produce a marbling effect.
Preparation:
A batt washed ceramic shelf is the best surface. You can use fibre paper on your shelf, but you must be careful to avoid raking deeply enough so that you pick up the fibre and drag it into the glass.
Make a boundary with 10-12mm fibre board on your shelf. You can use strips - for the most efficient use of the board – or cut a shape from a sheet. If you are using strips, fasten them together with wire staples. This will resist the glass flowing at the edges.
Place the glass into the space created by the fibre board. You can place 10mm strips on edge to form very tight lines, you can shingle glass to give broader lines, or you can place the glass in a more random way to give quite different effects.
When shingling or placing glass randomly, it is often best to cut a sheet of iridised clear to lie on the bottom to ensure you have enough depth of glass. Placing the iridised side of glass down toward the shelf provides an additional release, and can give added interest to the back. Anything less than 8-10mm thick leaves the glass pulled away from the edges in the direction of the combing.
Firing:
The initial temperature rise can be fast because the glass is made up of narrow strips. No bubble squeeze is required for the vertical or shingled strips, as there are easy ways for the air to escape. Randomly placed glass should have a bubble squeeze at around 650°-675°C for 30 minutes at least. Otherwise you can fire at about 300°C/hr to 925°C.
You need to programme a soak at that temperature for approximately 120 minutes. This soak allows you to do the combing and have the kiln recover temperature without needing to re-programme. When the combing is finished you cancel the soak after the kiln recovers to 925°C (which allows any peaks generated during the combing to settle down).
Allow or programme the kiln to cool as fast as it can to the annealing temperature and soak for 120 to 180 minutes. Set the annealing cool at 30°C/hour down to 450°C, then 60°C/hour to 370°C and finally at 200°C/hr to 21°C.
Combing:
Safety first. You must do you combing in a kiln that has a safety switch to turn the power off once the lid is opened a short way. If your kiln does not have such a safety device you should reconsider your desire to comb in your kiln. Many say you can overcome this by switching your kiln on and off at the wall socket. However, in doing so you also turn off the controller, making it necessary to re-programme your kiln each of the several times you have to reach into the kiln with your raking tool. This is essentially impractical.
The combing tool is a pointed steel rod, bent at right angles to the shaft - often called a rake. The shaft should be of wood to avoid holding a hot metal rod in your hand. Stainless steel rods are best as mild steel can spall and leave flakes of metal in or on the glass. The rod and wooden handle should be soaked in water while the kiln is heating up. The wet wood will not char so quickly as the dry. This bucket of water should remain beside the kiln so you can cool the metal point, when it begins to stick.
The second bit of safety. You will need to wear gear to protect yourself against the heat. A full face visor is important as the heat will singe you hair. You need to have heat resistant gloves. You need to have heat resistant sleeves to go over your arms. You should wear only natural fibres - cotton and wool are best, as they smoke before bursting into flame, giving you some warning that things are just too hot. An assistant to hold the kiln door/lid open while combing is advisable. And the assistant should have the same heat resistant gear that you have.
You begin to do the combing at 900°C. The glass will be soft enough to be pulled by a gentle stroke across the surface of the glass. Avoid digging into the glass. That will pull or push a gather of glass ahead of point. This leaves a characteristic droplet shaped mark in the glass at the end of the stroke. It may also go deeply enough that the kiln wash or fibre paper that is underneath the glass will be pulled up into the glass. Only light pressure is required to do the combing.
You will only be able to do a few strokes with the rake before the temperature of the glass falls and the glass resists movement. When the glass becomes difficult to move, it is time to close the lid and let the temperature recover. You will have to do this numerous times, until you have the look you want.
Another limitation is the speed that the rake metal heats up. When the metal becomes hot, it sticks to the glass. Whenever the rake is not in use, it should be in the bucket of water cooling off, and re-wetting the wooden handle.
You can comb the glass in any manner you wish. To get the traditional feathered look, you need to alternately pull and push the rake to give chevrons in opposite directions. Experienced people sometimes use two rakes – one to pull and one to push - at the same time. You can also rake diagonally across the sheet and even across the previous rakings. Some experimentation will show which effects you like best.
Preparation:
A batt washed ceramic shelf is the best surface. You can use fibre paper on your shelf, but you must be careful to avoid raking deeply enough so that you pick up the fibre and drag it into the glass.
Make a boundary with 10-12mm fibre board on your shelf. You can use strips - for the most efficient use of the board – or cut a shape from a sheet. If you are using strips, fasten them together with wire staples. This will resist the glass flowing at the edges.
Place the glass into the space created by the fibre board. You can place 10mm strips on edge to form very tight lines, you can shingle glass to give broader lines, or you can place the glass in a more random way to give quite different effects.
When shingling or placing glass randomly, it is often best to cut a sheet of iridised clear to lie on the bottom to ensure you have enough depth of glass. Placing the iridised side of glass down toward the shelf provides an additional release, and can give added interest to the back. Anything less than 8-10mm thick leaves the glass pulled away from the edges in the direction of the combing.
Firing:
The initial temperature rise can be fast because the glass is made up of narrow strips. No bubble squeeze is required for the vertical or shingled strips, as there are easy ways for the air to escape. Randomly placed glass should have a bubble squeeze at around 650°-675°C for 30 minutes at least. Otherwise you can fire at about 300°C/hr to 925°C.
You need to programme a soak at that temperature for approximately 120 minutes. This soak allows you to do the combing and have the kiln recover temperature without needing to re-programme. When the combing is finished you cancel the soak after the kiln recovers to 925°C (which allows any peaks generated during the combing to settle down).
Allow or programme the kiln to cool as fast as it can to the annealing temperature and soak for 120 to 180 minutes. Set the annealing cool at 30°C/hour down to 450°C, then 60°C/hour to 370°C and finally at 200°C/hr to 21°C.
Combing:
Safety first. You must do you combing in a kiln that has a safety switch to turn the power off once the lid is opened a short way. If your kiln does not have such a safety device you should reconsider your desire to comb in your kiln. Many say you can overcome this by switching your kiln on and off at the wall socket. However, in doing so you also turn off the controller, making it necessary to re-programme your kiln each of the several times you have to reach into the kiln with your raking tool. This is essentially impractical.
The second bit of safety. You will need to wear gear to protect yourself against the heat. A full face visor is important as the heat will singe you hair. You need to have heat resistant gloves. You need to have heat resistant sleeves to go over your arms. You should wear only natural fibres - cotton and wool are best, as they smoke before bursting into flame, giving you some warning that things are just too hot. An assistant to hold the kiln door/lid open while combing is advisable. And the assistant should have the same heat resistant gear that you have.
You begin to do the combing at 900°C. The glass will be soft enough to be pulled by a gentle stroke across the surface of the glass. Avoid digging into the glass. That will pull or push a gather of glass ahead of point. This leaves a characteristic droplet shaped mark in the glass at the end of the stroke. It may also go deeply enough that the kiln wash or fibre paper that is underneath the glass will be pulled up into the glass. Only light pressure is required to do the combing.
You will only be able to do a few strokes with the rake before the temperature of the glass falls and the glass resists movement. When the glass becomes difficult to move, it is time to close the lid and let the temperature recover. You will have to do this numerous times, until you have the look you want.
Another limitation is the speed that the rake metal heats up. When the metal becomes hot, it sticks to the glass. Whenever the rake is not in use, it should be in the bucket of water cooling off, and re-wetting the wooden handle.
You can comb the glass in any manner you wish. To get the traditional feathered look, you need to alternately pull and push the rake to give chevrons in opposite directions. Experienced people sometimes use two rakes – one to pull and one to push - at the same time. You can also rake diagonally across the sheet and even across the previous rakings. Some experimentation will show which effects you like best.
Friday, 5 June 2009
Annealing Open Face Castings
You need to double the annealing time for an open-faced casting over the schedules for the same thickness, because the glass is cooling from one side only. The usual schedules are premised on cooling from both sides equally. The schedules given for 50mm thick open face castings should be used for a 25mm thick open face casting.
If you could cover your open-faced casting with something of equivalent insulation as the investment around the glass you could go back to a 1" schedule.
So an open-faced casting 25mm thick needs to be annealed using the schedule for 50mm thick castings as follows (for Bullseye glass - make adjustments for different glasses):
482°C for 8 hrs
4°C/hr to 427°C
7°C/hr to 370°C
23°C/hr to 21°C
See the Bullseye chart for annealing thick pieces.
Based on Don Burt’s work
If you could cover your open-faced casting with something of equivalent insulation as the investment around the glass you could go back to a 1" schedule.
So an open-faced casting 25mm thick needs to be annealed using the schedule for 50mm thick castings as follows (for Bullseye glass - make adjustments for different glasses):
482°C for 8 hrs
4°C/hr to 427°C
7°C/hr to 370°C
23°C/hr to 21°C
See the Bullseye chart for annealing thick pieces.
Based on Don Burt’s work
Monday, 1 June 2009
Cutting Oil
Why use a cutting fluid?
No matter how good a fissure is when scored dry, it is better if scored with a liquid between the wheel and the glass. Several good things happen with an "oil" cut and only one undesirable thing.
The bad thing is you have to wash the glass afterwards, but in many cases washing is required anyway.
A good thing is the fluid reduces the effect of healing - the compressive strength overcoming the fracture caused by scoring. It is probable that the liquid seeps into the fissure contaminating it enough to prevent atomic reattachment of the molecules.
Cutting oil reduces chipping and prevents a flaky score line. The oil tends to provide a hydraulic cushion between the glass and the wheel. This allows more uniform transmission of the shearing forces into the glass at an angle dictated by the wheel, not by particles of crushed glass.
It is important to check the cutter wheel is moving freely, since a wheel not rolling freely may skid. Skidding causes abnormal wear to the wheel and subsequently it becomes a skipper.
You should not use kerosene by itself because it removes whatever oil is on the axle.
Prepared from information provided by Fletcher-Terry company
No matter how good a fissure is when scored dry, it is better if scored with a liquid between the wheel and the glass. Several good things happen with an "oil" cut and only one undesirable thing.
The bad thing is you have to wash the glass afterwards, but in many cases washing is required anyway.
A good thing is the fluid reduces the effect of healing - the compressive strength overcoming the fracture caused by scoring. It is probable that the liquid seeps into the fissure contaminating it enough to prevent atomic reattachment of the molecules.
Cutting oil reduces chipping and prevents a flaky score line. The oil tends to provide a hydraulic cushion between the glass and the wheel. This allows more uniform transmission of the shearing forces into the glass at an angle dictated by the wheel, not by particles of crushed glass.
It is important to check the cutter wheel is moving freely, since a wheel not rolling freely may skid. Skidding causes abnormal wear to the wheel and subsequently it becomes a skipper.
You should not use kerosene by itself because it removes whatever oil is on the axle.
Prepared from information provided by Fletcher-Terry company
Subscribe to:
Posts (Atom)